NoticeITEADUINO PLUS ARDUINO PLUG
From ITEAD Wiki
Contents
Overview
Iteaduino Plus Arduino Plug is specifically designed for A10/A20 evaluation board. It adapts Raspberry Pi interface on A10/A20 evaluation board to Arduino interface, which facilitates development as Arduino. There is an OLED screen and Grove interface of electronic brick, which is beneficial to prototyping development.
Specifications
| PCB size | 109.3mm X 76.2mm X 1.6mm |
| Operating level | 3.3V |
| Interface | 4-pin Grove interface, XBee interface and Raspberry Pi interface |
Hardware
pinMap
| Index of Interface | Definition in | Name of Raspberry PI Interface | Index of Arduino |
| Iteaduino Plus | |||
| 1 | 3V3 | 3.3V | 3.3V |
| 2 | 5V | 5V | 5V |
| 3 | SDA0/68 | SDA0 | A4 |
| 4 | 5V | DNC | 5V |
| 5 | SCL0/67 | SCL0 | A5 |
| 6 | GND | GND | GND |
| 7 | 20 | GPIO7 | D9 |
| 8 | UART4_TX/89 | TX | D1 |
| 9 | GND | DNC | GND |
| 10 | UART4_RX/90 | RX | D0 |
| 11 | 9 | GPIO0 | D2 |
| 12 | 10 | GPIO1 | D3 |
| 13 | 11 | GPIO2 | D4 |
| 14 | GND | DNC | GND |
| 15 | 14 | GPIO3 | D5 |
| 16 | 15 | GPIO4 | D6 |
| 17 | DNC | DNC | 3.3V |
| 18 | 16 | GPIO5 | D7 |
| 19 | SPI0_MOSI/111 | MOSI | D11 |
| 20 | GND | DNC | GND |
| 21 | SPI0_MISO/112 | MISO | D12 |
| 22 | 19 | GPIO6 | D8 |
| 23 | SCL/110 | SCLK | D13 |
| 24 | SPI0_CS0/109 | SPI0_CE0 | D10 |
| 25 | GND | DNC | GND |
| 26 | SPI0_CS1/137 | SPI0_CE1 | A3 |
XBee Interface
| Index of Interface | Definition in Iteaduino Plus | Name of Arduino | Index of XBee |
| 1 | 3.3V | 3.3V | 3.3V |
| 2 | GND | GND | GND |
| 3 | UART4_RX/90 | D0 | XBee_Dout |
| 4 | UART4_TX/89 | D1 | XBee_Din |
| 5 | SPI0_CS1/137 | A3 | XBee_RST |
OLED Interface
| Index of Interface | Definition in Iteaduino Plus | Name of Arduino | Index of OLED |
| 1 | 3.3V | 3.3V | 3.3V |
| 2 | GND | GND | GND |
| 3 | SDA0/68 | A4 | OLED_SDA |
| 4 | SCL0/67 | A5 | OLED_SCL |
| 5 | 11 | D4 | OLED_RST |
Operating level switch
By sliding the switch, the power voltage at V pin on the electronic brick will also be changed. When switching to 3,3V, voltage at V pin will be 3.3V and it will be 5V when switching to 5V.
Button
- XBee_RST
Reset button of XBee module, press it to reset the module.
Compatibility
Arduino Plug’s compatibility with shields in iMall is shown as below:
| SKU | Name | Compatibility |
| IM120417014 | ITEAD Joystick shield | N |
| IM120417023 | IBridge lite | Y |
| IM120417015 | Arduino Dual Step Motor Driver Shield | Y |
| IM120417022 | IS Shield | Y |
| IM120417017 | Arduino GPS shield | Y |
| IM120417021 | 3.2 TFT LCD Touch Shield | N |
| IM120417018 | Arduino 1602 LCD Shield | N |
| IM120417020 | 2.8 TFT LCD Touch Shield | N |
| IM120417019 | Arduino USB Host Shield | Y |
| IM120628001 | Arduino Mega Sensor Shield | N |
| IM120628002 | Arduino Sensor Shield V4 | Y |
| IM120704001 | BT BoosterPack | N |
| IM120417013 | Arduino Proto Screw Shield | Y |
| IM120417024 | ITDB02 Arduino MEGA Shield | N |
| IM120417012 | 2.4 TFT LCD Touch shield | N |
| IM120417007 | Stackable SD Card shield | Y |
| IM120417006 | BT Shield (Slave) | Y |
| IM120417008 | ITDB02 Arduino Shield | N |
| IM120417005 | MotoMama | Y |
| IM120417009 | IComSat | Y |
| IM120417004 | XBee Shield | Y |
| IM120417010 | BT Shield (Master Slave) | Y |
| IM120417002 | Colors Shield | N |
| IM120417001 | IBridge | N |
| IM120417003 | IE Shield | Y |
| IM120417016 | Arduino Nano IO Shield | N |
| IM120911007 | W5100 Ethernet Shield | Y |
| IM121010001 | WIFI Shield REV2 | Y |
| IM121026001 | ITEAD Music Player Shield | N |
| IM121026002 | ITEAD 3G Shield | Y |
| IM121115001 | ITEAD Power Shield | Y |
| IM121211001 | ITEAD Arduino Sensor Shield | Y |
| IM130704001 | ITEAD BLE Shield | Y |
| IM130715001 | Mega Proto Screw Shield | N |
Download
Datasheet for ITEADUINO PLUS ARDUINO PLUG
Schematic for ITEADUINO PLUS ARDUINO PLUG
