NoticeDifference between revisions of "ITEADUINO PLUS ARDUINO PLUG"
From ITEAD Wiki
(→Operating level switch) |
(→Operating level switch) |
||
| Line 120: | Line 120: | ||
==Operating level switch== | ==Operating level switch== | ||
http://imall.iteadstudio.com/media/wysiwyg/Products/ARM/IM131016001_2.jpg | http://imall.iteadstudio.com/media/wysiwyg/Products/ARM/IM131016001_2.jpg | ||
| + | |||
By sliding the switch, the power voltage at V pin on the electronic brick will also be changed. When switching to 3,3V, voltage at V pin will be 3.3V and it will be 5V when switching to 5V. | By sliding the switch, the power voltage at V pin on the electronic brick will also be changed. When switching to 3,3V, voltage at V pin will be 3.3V and it will be 5V when switching to 5V. | ||
Revision as of 07:59, 21 May 2014
Contents
Overview
Iteaduino Plus Arduino Plug is specifically designed for A10/A20 evaluation board. It adapts Raspberry Pi interface on A10/A20 evaluation board to Arduino interface, which facilitates development as Arduino. There is an OLED screen and Grove interface of electronic brick, which is beneficial to prototyping development.
Specifications
| PCB size | 109.3mm X 76.2mm X 1.6mm |
| Operating level | 3.3V |
| Interface | 4-pin Grove interface, XBee interface and Raspberry Pi interface |
Hardware
pinMap
| Index of Interface | Definition in | Name of Raspberry PI Interface | Index of Arduino |
| Iteaduino Plus | |||
| 1 | 3V3 | 3.3V | 3.3V |
| 2 | 5V | 5V | 5V |
| 3 | SDA0/68 | SDA0 | A4 |
| 4 | 5V | DNC | 5V |
| 5 | SCL0/67 | SCL0 | A5 |
| 6 | GND | GND | GND |
| 7 | 20 | GPIO7 | D9 |
| 8 | UART4_TX/89 | TX | D1 |
| 9 | GND | DNC | GND |
| 10 | UART4_RX/90 | RX | D0 |
| 11 | 9 | GPIO0 | D2 |
| 12 | 10 | GPIO1 | D3 |
| 13 | 11 | GPIO2 | D4 |
| 14 | GND | DNC | GND |
| 15 | 14 | GPIO3 | D5 |
| 16 | 15 | GPIO4 | D6 |
| 17 | DNC | DNC | 3.3V |
| 18 | 16 | GPIO5 | D7 |
| 19 | SPI0_MOSI/111 | MOSI | D11 |
| 20 | GND | DNC | GND |
| 21 | SPI0_MISO/112 | MISO | D12 |
| 22 | 19 | GPIO6 | D8 |
| 23 | SCL/110 | SCLK | D13 |
| 24 | SPI0_CS0/109 | SPI0_CE0 | D10 |
| 25 | GND | DNC | GND |
| 26 | SPI0_CS1/137 | SPI0_CE1 | A3 |
XBee Interface
| Index of Interface | Definition in Iteaduino Plus | Name of Arduino | Index of XBee |
| 1 | 3.3V | 3.3V | 3.3V |
| 2 | GND | GND | GND |
| 3 | UART4_RX/90 | D0 | XBee_Dout |
| 4 | UART4_TX/89 | D1 | XBee_Din |
| 5 | SPI0_CS1/137 | A3 | XBee_RST |
OLED Interface
| Index of Interface | Definition in Iteaduino Plus | Name of Arduino | Index of OLED |
| 1 | 3.3V | 3.3V | 3.3V |
| 2 | GND | GND | GND |
| 3 | SDA0/68 | A4 | OLED_SDA |
| 4 | SCL0/67 | A5 | OLED_SCL |
| 5 | 11 | D4 | OLED_RST |
Operating level switch
By sliding the switch, the power voltage at V pin on the electronic brick will also be changed. When switching to 3,3V, voltage at V pin will be 3.3V and it will be 5V when switching to 5V.
