Difference between revisions of "Wee Serial WIFI Module"

From ITEAD Wiki
Jump to: navigation, search
m (Instruction)
m (Instruction)
Line 106: Line 106:
 
AT Commands--http://wiki.iteadstudio.com/ESP8266_Serial_WIFI_Module
 
AT Commands--http://wiki.iteadstudio.com/ESP8266_Serial_WIFI_Module
  
How to upgrade ESP8266 firmware?
+
'''How to upgrade ESP8266 firmware?'''
  
We provide a ESP8266 firmware upgrading tools here. Please download and install it in your computer. You should pay attention that this software is chinese version and it only run on Windows environment.
+
We provide a ESP8266 firmware upgrading tools here. Please download and install it in your computer. You should pay attention that this software is '''chinese version''' and it only runs on Windows environment.
 +
 
 +
[[:File:ESP8266Flasher-x86-v0.9.2.3.zip]]
  
 
In this instruction, we will demonstrate the firmware upgrading by using Wee and Foca Pro.  
 
In this instruction, we will demonstrate the firmware upgrading by using Wee and Foca Pro.  
  
Plug the Wee in Foca Pro, then make sure that the switch level is 3.3 V in Foca Pro and the Wee is in FW mode.
+
*Plug the Wee in Foca Pro, then make sure that the switch level is 3.3 V in Foca Pro and the Wee is in FW mode.
  
 
[[File:IM141118001pic6.jpg|600px]]
 
[[File:IM141118001pic6.jpg|600px]]
  
Open the software, choose the right COM and click the button that is circled in the following picture. When a tick appears in the bottom-left corner, it suggest that the firmware upgrade successfully.
+
*Open the software, choose the right COM and click the button that is circled in the following picture. When a tick appears in the bottom-left corner, it suggests that the firmware upgrade successfully.
 +
 
 +
[[File:Upgrade Firmware.jpg|600px]]
 +
 
 +
*This software contains an '''existing firmware''', but if you want to upgrade other ESP8266 firmware, please click the button that is circled in the following picture, and only two file path are available to choose.
 +
 
 +
[[File:Upgrade Firmware 1.jpg|600px]]
  
 
==Download==
 
==Download==
 
Schematic--[[:File:IM141118001-Wee-Schematic.pdf]]
 
Schematic--[[:File:IM141118001-Wee-Schematic.pdf]]

Revision as of 07:25, 14 January 2015

Overview

IM141118001 3.jpg

Wee is a WIFI module based on ESP8266 SoC. ESP8266 comes out of nowhere and has been taking by storm the IoT world. You can find many hacking projects about it on the internet. So far, the most popular ESP8266 breakout version only has GPIO0 and GPIO2 routed to the header. Compared to it, Wee WIFI module is designed with a standard Bee interface and has more GPIOs available for developers. In a word, users can take full use of the utility of ESP8266 SoC by using Wee WIFI module in your projects.

Go shopping Wee Serial WIFI Module

Features

  • Standard Bee interface
  • indicators: TX, RX, PWR
  • FW/Work Switch
  • More GPIOs help developer take full use of the utility of ESP8266 SoC

Specification

PCB Size 23.9X26.2X1.6mm
Interface Bee interface
Indicators PWR,TX,RX

Electrical Characteristics

Characteristics Symbol Min Typ Max Unit
Power supply voltage VDD 3 3.3 3.5 V
High input voltage VIH 0.8XVDD - VDD V
Low input voltage VIL 0 - 0.2XVDD V
Operation current for VDD IDD - - 215 mA

Hardware

IM141118001pic1.jpg IM141118001pic2.jpg IM141118001pic4.jpg

Note

  • Work/FW Switch
When burn firmware into ESP8266, you should ensure the switch is in FW mode.
For the normal usage of this module, you should ensure the switch is in work mode.

Pin Map

Pin Index Pin Name Description
1 3V3
2 TX
3 RX
4 -
5 RST# Enable wee module to reset in low level
6 -
7 FW Firmware enable pin*
8 -
9 -
10 GND
11 -
12 -
13 MTMS
14 GPIO2
15 -
16 -
17 -
18 MTD0
19 MTCK
20 MTDI

Note:

  • Firmware enable pin
When set to 0, power or reset the wee module, you can access to the firmware uploading mode;
When set to 1, power or reset the wee module, you can access to the normal work mode

Instruction

AT Commands--http://wiki.iteadstudio.com/ESP8266_Serial_WIFI_Module

How to upgrade ESP8266 firmware?

We provide a ESP8266 firmware upgrading tools here. Please download and install it in your computer. You should pay attention that this software is chinese version and it only runs on Windows environment.

File:ESP8266Flasher-x86-v0.9.2.3.zip

In this instruction, we will demonstrate the firmware upgrading by using Wee and Foca Pro.

  • Plug the Wee in Foca Pro, then make sure that the switch level is 3.3 V in Foca Pro and the Wee is in FW mode.

IM141118001pic6.jpg

  • Open the software, choose the right COM and click the button that is circled in the following picture. When a tick appears in the bottom-left corner, it suggests that the firmware upgrade successfully.

Upgrade Firmware.jpg

  • This software contains an existing firmware, but if you want to upgrade other ESP8266 firmware, please click the button that is circled in the following picture, and only two file path are available to choose.

Upgrade Firmware 1.jpg

Download

Schematic--File:IM141118001-Wee-Schematic.pdf