Difference between revisions of "Sonoff SV"

From ITEAD Wiki
Jump to: navigation, search
m (Features)
m
Line 117: Line 117:
 
[[File:Sonoff SV hardware.png|520px]]
 
[[File:Sonoff SV hardware.png|520px]]
  
==Soldering Instructions==
+
==Solder Instructions==
 
[[File:Sonoff-sv-soldering-guide.jpg|700px]]
 
[[File:Sonoff-sv-soldering-guide.jpg|700px]]
  

Revision as of 06:27, 15 March 2016

Overview

Sonoff SV (6).JPG

Sonoff SV(safe voltage) is a low power supply Sonoff version,which supports 5-24V power supply. The power separation circuit enables it to control AC or DC power for the connected device, but you need to do some welding to realize this function, please refer to Soldering Instructions below. Sonoff SV has GIPO reserved to support secondary development. This version does not have 433 RF function.

Go shopping Sonoff SV (SKU:IM160220004)

Features

-Support 5~24V power supply.

--Support fast configure SSID and password through APP.

-Support automatic connect to server, register and update status info.

-Support tracking device status and timely remote control through APP.

-Support setting single and repeat timing tasks.

-Reserve GIPO to support secondary development.

WIFI Characteristics

• 802.11 b / g / n

• Built-in Tensilica L106 ultra-low power consumption 32-bit micro-MCU, dominant frequency support 80 MHz and 160 MHz, support RTOS

• Built-in TCP / IP protocol stack

• Built-in TR switch, balun, LNA, power amplifier and matching network

• Built-in PLL, voltage regulator and power supply management components, 802.11b mode +20 dBm output power

• A-MPDU&A-MSDU aggregation and 0.4μs guard interval

• WiFi @ 2.4 GHz, supports WPA / WPA2 safe mode

• Support cloud OTA upgrade

• Support STA / AP / STA + AP mode

• UART, I2C, PWM, GPIO

• Deep sleep maintain current is 10 uA, shutdown current is less than 5 uA

• Wake-up, connect and transfer data packets in 2 ms

• Standby power consumption is less than 1.0 mW (DTIM3)

• Operating temperature range: -40 ℃ - 125 ℃

• Other parameters as follows

Category Parameters Description
Wireless Parameter Wireless standard 802.11 b/g/n
Frequency range 2.4GHz-2.5GHz (2400M-2483.5M)
Hardware Parameter Data port UART/I2C
GPIO/PWM
Operating voltage 3.0~3.6V(recommend 3.3V)
Operating current Average: 80mA
Operating temperature -40°~125°
Storage temperature Room temperature
Package size 65mm*34mm*16mm
Software Parameter Wireless network mode station/softAP/SoftAP+station
Security mechanism WPA/WPA2
Encryption type WEP/TKIP/AES
Firmware upgration Local serial programming/Cloud Upgrade/Host download programming
Software development Support secondary development
Network protocols IPv4, TCP/UDP/HTTP/FTP
User configuration cloud server, Android/iOS APP

Specification

PCB Size 65X34X1.2mm
Interface UART
Indicator LED WiFi,on/off

Electrical Characteristics

Characteristics Symbol Min Typ Max Unit
Power supply voltage VDD 5 - 24 V
Operation current for VDD IDD - - 290 mA

Hardware

Sonoff SV hardware.png

Solder Instructions

Sonoff-sv-soldering-guide.jpg

This is a development board, so you can do some soldering to realize different functions.

Work Mode:

Default mode: WIFI circuit and relay circuit adopt the same power supply. You can connect the power supply to J2 or J4. If the input voltage range is within 5-24V, J8 must connect to the jumper; If the input voltage range is within 4-5V, you need to disconnect J8 jumper.

Isolated Mode: 

WIFI circuit and relay circuit can be isolated by removing R17 and R22.  You will have to power them separately. You can power relay circuit by J2 and power WIFI circuit by J8. 

V:3.3V G:GND S:Single

Pin Map

Pin Index Pin Name Description
1 3V3 Chip power
2 TX Serial transmit port
3 RX Serial receiving port
4 GND GND
5 GPIO4 I/O
6 GPIO5 I/O
7 GPIO14 I/O

Downloads

File:Sonoff SV-Dimension.pdf

File:Sonoff SV Schematic.pdf

File:Sonoff SV-VIEW.pdf

Useful Links

User Manual for Sonoff and Slampher