POE W5500 Ethernet Shield

From ITEAD Wiki
Revision as of 06:24, 22 October 2014 by ITead (Talk | contribs)

Jump to: navigation, search

Overview

IM140725004 4.jpg

W5500 Ethernet shield is a WIZnet W5500 breakout board with POE and Micro-SD designed for Arduino platform. 5V/3.3V compatible operation voltage level makes it compatible with Arduino boards, leafmaple, and other Arduino compatible board.

WIZnet„s Hardwired TCP/IP is the market-proven technology that supports TCP, UDP, IPv4, ICMP, ARP, IGMP, and PPPoE protocols. W5500 embeds the 32Kbyte internal memory buffer for the Ethernet packet processing. If you use W5500, you can implement the Ethernet application just by adding the simple socket program. It’s faster and easier way rather than using any other Embedded Ethernet solution. Users can use 8 independent hardware sockets simultaneously.

Go shopping [POE W5500 Ethernet Shield(IM140725005)]

Features

  • 3.3/5V level
  • On-board micro SD card slot
  • Support Endspan and Midspan Modes POE power supply
  • Supports following Hardwired TCP/IP Protocols: TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
  • Supports 8 independent sockets simultaneously
  • Supports Power down mode
  • Supports Wake on LAN over UDP
  • Supports High Speed Serial Peripheral Interface (SPI MODE 0, 3)
  • Internal 32Kbytes Memory for Tx/Rx Buffers
  • 10BaseT/100BaseTX Ethernet PHY embedded
  • Support Auto Negotiation (Full and half duplex, 10 and 100-based)
  • Not support IP Fragmentation

Specification

PCB size 83.82mm X 57.91mm X 1.6mm
Power supply 5V DC
Indicator SPD,LINK,DUP,ACT
Communication Protocol SPI

Electronic Characteristics

Parameter Min. Typical Max. Unit
Power supply 4.5 5 5.5 VDC
Input voltage VinH(Target voltage=3.3V) 3 3.3 3.6 V
Input voltage VinH(Target voltage=5V) 4.5 5 5.5 V
Input voltage VinL -0.3 0 0.5 V
Current Consumption - - 150 mA

Hardware

IM140725005pic1.jpg IM140725004pic3.jpg

  • Indicator LED
- SPD:Speed LED. This shows the speed status of the connected link.
ON:100Mbps
OFF:10Mbps
- LINK:Link LED. This shows the Link status.
ON:Link is established
OFF:Links is not established
- DUP:Duplex LED. This shows the Duplex status for the connected link.
ON:Full-duplex mode
OFF:Half-duplex mode
- ACT:Active LED. This shows that there is carrier sense(CRS) from the active Physical Medium Sub-layer(PMD) during TX or RX activity.
ON:Carrier sense from the active PMD
OFF:No carrier sense
  • Reset
It will reset W5500 if you press this button.

Pin Map

Pin Description
D0 Rx/Breakout
D1 TX/Breakout
D4 SD_CS
D10 W5500_CS
D11 SPI MOSI
D12 SPI MISO
D13 SPI SCK
A0 Breakout
A1 Breakout
A2 Breakout
A3 Breakout
A4 IIC_SDA/Breakout
A5 IIC_SCL/Breakout
A0 Breakout

Installation

When install W5500 Ethernet shield to Iteaduino, please check the operation voltage level of development board. If the voltage is 3.3V (IFLAT32,Leafmaple), set the Operation Level Setting switch to 3.3V. If the voltage is 5V(Arduino), set the Operation Level Setting switch to 5V.

Iteaduino communicates with both the W5500 and SD card using the SPI bus. This is on digital pins 11, 12, and 13 on the UNO/Duemilanove and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5500 and pin 4 for the SD card. These pins cannot be used for general I/O. On the Mega, the hardware SS pin, 53, is not used to select either the W5500 or the SD card, but it must be kept as an output.

Note that because the W5100 and SD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W5500, set digital pin 10 as a high output.

For some of the Arduino boards, SPI is on ICSP and D11 ~ D13, while for some main boards, D11 D12 / D13 are not defined as SPI. In order to improve the compatibility, we design an SPI JUMPER to make it compatible with mainboards of the two different types.For details, please find the table below.

Index Arduino Board Operation Voltage Switch SPI JUMPER
1 Arduino UNO 5V Don’t care
2 Arduino Leonardo 5V Disconnected
3 Arduino MEGA 5V Disconnected
4 Arduino DUE 3.3V Disconnected
5 Iteaduino UNO 5V/3.3V Don’t care
6 Iteaduino Leonardo 5V/3.3V Disconnected
7 Iteaduino MEGA 2560 5V/3.3V Connected
8 Iteaduino DUE 3.3V Disconnected
9 Iteaduino BT 5V/3.3V Don’t care
10 Iteaduino ADK 5V Disconnected
11 ChipKit UNO32 3.3V Don’t care
12 ChipKit MAX32 3.3V Disconnected

Instruction