Difference between revisions of "Non Blind Zone Ultrasonic Module SDM-IO 5pin"

From ITEAD Wiki
Jump to: navigation, search
(Created page with "==Overview== right Non Blind Zone Ultrasonic Module SDM-IO is a stable and measuring the distance accurate...")
 
m (User Guide)
 
(One intermediate revision by the same user not shown)
Line 18: Line 18:
 
==User Guide==
 
==User Guide==
  
There are 5 pins in this [[Non Blind Zone Ultrasonic Module SDM-IO]]. 1-2cm can't be measured. For now, Oc pin needs to be hacked.
+
There are 5 pins in this [[Non Blind Zone Ultrasonic Module SDM-IO]]. 1-2cm can't be measured. For now, Oc pin still needs to be hacked.
  
 
[[File:IM120628006pic1.png|400px]]
 
[[File:IM120628006pic1.png|400px]]
Line 24: Line 24:
 
'''Work with [[Iteaduino UNO]] (Arduino UNO)'''
 
'''Work with [[Iteaduino UNO]] (Arduino UNO)'''
  
*connection: VCC->3.3/5V    Echo->D2    Trig->D3    GND->GND
+
*Connection: VCC->3.3/5V    Echo->D2    Trig->D3    GND->GND
  
 
[[File:IM120628006pic2.jpg|500px]]
 
[[File:IM120628006pic2.jpg|500px]]
Line 86: Line 86:
  
 
</pre>
 
</pre>
 +
 +
*Open serial port monitor to check the distance.
 +
 +
[[File:IM120628006pic3.png|400px]]

Latest revision as of 08:08, 17 March 2015

Overview

NON BLIND ZONE ULTRASONIC MODULE SDM-IO.jpg

Non Blind Zone Ultrasonic Module SDM-IO is a stable and measuring the distance accurately ultrasonic module which provides 0cm - 1500mm non-contact measurement function,the ranging accuracy can reach to 3mm. Its performance can compare with SRF05/SRF02 ultrasonic distance measuring module, also it has non-blind (From 0-1cm the measurement results are not accurate when we test, but more than 1cm are accurate) design and fast response.

Go shopping Non Blind Zone Ultrasonic Module SDM-IO (IM120628006)

Specification

  • Operation Voltage DC 3 - 5.5 V
  • Global Current Consumption 8 mA
  • Ultrasonic Frequency 40k Hz
  • Maximal Range 3000 mm
  • Minimal Range 0 cm
  • Resolution 1 mm
  • Trigger Pulse Width 10 μs
  • Sensor Angle 15 degrees
  • TTL level output

User Guide

There are 5 pins in this Non Blind Zone Ultrasonic Module SDM-IO. 1-2cm can't be measured. For now, Oc pin still needs to be hacked.

IM120628006pic1.png

Work with Iteaduino UNO (Arduino UNO)

  • Connection: VCC->3.3/5V Echo->D2 Trig->D3 GND->GND

IM120628006pic2.jpg

const int TrigPin = 3;   // connect TrigPin to D3
const int EchoPin = 2; 	// connect EchoPin to D2
unsigned long time;
float cm; 
boolean result=true;
void setup() 
{ 
Serial.begin(9600); 
pinMode(TrigPin, OUTPUT); 
pinMode(EchoPin, INPUT); 

} 
void loop() 
{ 
digitalWrite(TrigPin, HIGH);  //output a at least 10us low pulse to triger the ultrasonic wave
delayMicroseconds(100); 
digitalWrite(TrigPin, LOW); 
delayMicroseconds(10); 
digitalWrite(TrigPin, HIGH); 
time = micros();
attachInterrupt(0, echo, FALLING);
while(result==false)
{
  if((micros()-time)>=50000)
  break;
  
}


if(result == true)
{
  
cm = time / 58.0; //turn echo time into unit cm 
cm = (int(cm * 100.0)) / 100.0; //reserves two decimal fractions
if(cm>=(3.8+2.0))		//calibration
{cm-=3.8;}
else
{cm=0.0;}
Serial.print(cm); 
Serial.print("cm"); 
Serial.println(); 

delay(1000); 
result=false;
}

} 
void echo()			//test the echo time from trig=1 to echo=0
{
  result=true;
  time=micros()-time;
  detachInterrupt(0);
}

  • Open serial port monitor to check the distance.

IM120628006pic3.png