Difference between revisions of "MotoMama"

From ITEAD Wiki
Jump to: navigation, search
(Overview)
m (Download)
 
Line 213: Line 213:
 
[ftp://imall.iteadstudio.com/IM120417005_MotoMama/DS_L298N.pdf Datasheet for L298N]
 
[ftp://imall.iteadstudio.com/IM120417005_MotoMama/DS_L298N.pdf Datasheet for L298N]
  
[ftp://imall.iteadstudio.com/IM120417005_MotoMama/SCH_IM120417005_MotoMama.pdf Schematic for MotoMama]
+
[[:File:Motomama Shield 2.0.pdf | Schematic for MotoMama]]
  
 
[ftp://imall.iteadstudio.com/IM120417005_MotoMama/DC_MotoMama_Aruino_Test.zip Demo Code for MotoMama]
 
[ftp://imall.iteadstudio.com/IM120417005_MotoMama/DC_MotoMama_Aruino_Test.zip Demo Code for MotoMama]

Latest revision as of 07:48, 9 May 2016

Overview

MotoMama.jpg

MotoMama is an H-Bridge motor driver shield bases on ST L298N chip. It is a high voltage, high current dual full-bridge driver which designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC motor and stepping motors. MotoMama is designed to be easy with other sensors or wireless modules.

Go shopping MotoMama (IM120417005)

Features

  • Light Weight, small dimension
  • Super driver capacity
  • FED protection
  • Heavy load heat sink
  • 2 DC motor/4 coil dual phrase stepper motor output
  • Motor direction indication LED
  • Pulse protection
  • XBee/nRF24L01+ socket break out
  • UART/IIC/Ads socket break out
  • 4 standard mounting holes

Specifications

PCB size 80.36mm X 56.12mm X 1.6mm
Indicators PWR, Motor direction
Power supply 7~15V
Communication Protocol XBee, nRF24L01+,UART, IIC
RoSH Yes

Electrical Characteristics

Specification Min Type Max Unit
Power Voltage (Vlogic) 4.5 5 5.5 VDC
Power Voltage(Vsupply) 7 - 15 VDC
Input Voltage VH: 4.5 5 5.5 V
Input Voltage VL: -0.3 0 0.5 V
Current Consumption - - 2000 mA

Hardware

IM120417005_MotoMamapin.jpg

Figure 1 Top Map

MotoMama1.jpg

Figure 2 Bottom Map

Interface Pin Description
UART 1 5V supply
UART 2 Ground
UART 3 Tx
UART 4 Rx
AD0/1/2 1 AD0/1/2
AD0/1/2 2 5V supply
AD0/1/2 3 Ground
IIC 1 Ground
IIC 2 5V supply
IIC 3 Data wire of IIC
IIC 4 Clock wire of IIC
nRF24L01+ Socket 1 GND
nRF24L02+ Socket 2 VCC33
nRF24L03+ Socket 3 CE(Chip Enable)
nRF24L04+ Socket 4 SPI_CS
nRF24L05+ Socket 5 SPI_SCK
nRF24L06+ Socket 6 SPI_MOSI
nRF24L07+ Socket 7 SPI_MISO
nRF24L07+ Socket 8 nRF24L01+ IRQ Output
XBee Socket 1 VCC33
XBee Socket 2 Dout
XBee Socket 3 Din
XBee Socket 10 GNF
XBee Socket 4,5,6,7,8,9,11,12,13,14,15,16,17,18,19,20 No Connect

Arduino Socket definition

Pin Description
D0 XBee_Dout/UART_Rx
D1 XBee_Din/UART_Tx
D2 nRF24L01+_MISO
D3 nRF24L01+_MOSI
D4 nRF24L01+_SCK
D5 nRF24L01+_CS
D6 nRF24L01+_CE
D7 NC
D8 In1
D9 In2
D10 EnA
D11 EnB
D12 In3
D13 In4
A0 AD0
A1 AD1
A2 AD2
A3 AD3
A4 IIC_SCL
A5 IIC_SDA

Installation

MotoMama can drive two DC motors at the same time.

OUT1/OUT2 is completely symmetrical as OUT3/OUT4 on the board. These pins is connect to the DC motors. The output voltage depends on VIN.

DC motor control input port A has three pins, In1, In2 and EnA. In1 and In2 are digital ports which be used to control the direction of the motor, EnA is connecting with PWM port of control board to control the speed of motor.

EnA In1 In2 Description
0 X X Free Running Motor Stop
1 1 0 Forward
1 0 1 Reverse
1 In1=In2 In1=In2 Fast Motor Stop
EnB In3 In4 Description
0 X X Free Running Motor Stop
1 1 0 Forward
1 0 1 Reverse
1 In3=In4 In3=In4 Fast Motor Stop

Port A is used to control the motor that connect with OUT1 and OUT2, Port B is used to control the motor that connect with OUT3 and OUT4.

The EnA, EnB, ln1, ln2, ln3, ln4 can be used to drive the 4-wire stepping motor which connects with OUT1, OUT2, OUT3 and OUT4.

Download

Datasheet for MotoMama

Datasheet for L298N

Schematic for MotoMama

Demo Code for MotoMama

Useful Links

by Itead Studio <MotoMama And Makeblock 2WD Robot Kit>