Iteaduino UNO

From ITEAD Wiki
Revision as of 01:20, 20 May 2014 by Ivy (Talk | contribs)

Jump to: navigation, search

Overview

Iteaduino Uno is a microcontroller board based on the Arduino UNO. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

Features

  • New external IO pin map
  • Efficient DC-DC Power supply with wide range input
  • 3.3V/5V Operating Voltage selection
  • All pins out for Sensor and Servo
  • UART/IIC interface breakout

Spec

Microprocessor ATmega328,ATmega8U2
PCB size 68.58mm X 58.42mm X 1.6mm
Indicators Power,TX,RX,D13
Power supply(recommended) 7-23V DC
Power supply(limits) 23 VDC (max)
Communication Protocol UART,SPI,IIC
Clock Speed 16MHz

Electrical Characteristics

Specification Min. Typical Value Max. Unit
Input voltage 7 - 23 VDC
Operating Voltage - 3.3/5 - VDC
DC Current per I/O Pin - 40 - mA

Hardware

IteadunoUNO1.jpg

Digital/Servo Interface: D0~D13 pin

Sensor Interface: A0 A1 A2 A3 A4 A5 pin

Pin Map

Power

The Iteaduino Uno can be powered via the USB connection or with an external power supply. The power source is selected automatically. External (non-USB) power can come either from an AC-to-DC adapter (wall-wart) or battery. The adapter can be connected by plugging a 2.1mm center-positive plug into the board's power jack. Leads from a battery can be inserted in the Gnd and Vin pin headers of the POWER connector.

The board can operate on an external supply of 7 to 23 volts. If supplied with less than 7V, however, the 5V pin may supply less than five volts and the board may be unstable.

Power supply select switch:

Iteaduino UNO iteadstudio.com 2012-11-11 4 Tech Support: support@iteadstudio.com On Iteaduino UNO board, there is a supply power select switch for selecting the 3.3/5V power supply. Much compatible shields can be plug in Iteaduino UNO board.

The power pins are as follows:

  • VIN. The input voltage to the Iteaduino board when it's using an external power source (as opposed to 5 volts from the USB connection or other regulated power source). You can supply voltage through this pin, or, if supplying voltage via the power jack, access it through this pin.
  • 5V. This pin outputs a regulated 5V from the regulator on the board. The board can be supplied with power either from the DC power jack (7 - 12V), the USB connector (5V), or the VIN pin of the board (7-12V). Supplying voltage via the 5V or 3.3V pins bypasses the regulator, and can damage your board. We don't advise it.
  • 3V3. A 3.3 volt supply generated by the on-board regulator. Maximum current draw is 500 mA.
  • GND. Ground pins.

Memory

The ATmega328 has 32 KB (with 0.5 KB used for the bootloader). It also has 2 KB of SRAM and 1 KB of EEPROM.

Input and Output

Communication

Programming

Automatic (Software) Reset

USB Over-current Protection

Links and References

Download

Datasheet for Iteaduino UNO

Schematic for Iteaduino UNO

Fritzing Parts for Iteaduino UNO

Useful Link

<Fritzing Parts: ITEAD Development Board>