Difference between revisions of "ITDB02-2.4S/zh-cn"

From ITEAD Wiki
Jump to: navigation, search
(Created page with "==使用指南==")
(Created page with "<big>'''1.触摸功能'''</big> *把 '''2_4_spi_touch.ino''' 烧写进 UNO 主板 ::File:2_4_spi_touch.zip *然后按照以下的接线方式连接UNO和ITDB02-2.4S...")
Line 85: Line 85:
 
==使用指南==
 
==使用指南==
  
<big>'''1.Touch Function'''</big>
+
<big>'''1.触摸功能'''</big>
*Upload '''2_4_spi_touch.ino''' into UNO main board
+
*'''2_4_spi_touch.ino''' 烧写进 UNO 主板
 
::[[:File:2_4_spi_touch.zip]]
 
::[[:File:2_4_spi_touch.zip]]
*Connect [[ITDB02-2.4S]] module to UNO according to the table as below:
+
*然后按照以下的接线方式连接UNO和[[ITDB02-2.4S]]模块:
 
{| class="wikitable wikitable-indent"
 
{| class="wikitable wikitable-indent"
 
|-
 
|-
Line 119: Line 119:
 
|-
 
|-
 
|}
 
|}
*Power UNO mainboard, you can start to draw any line or pattern on the screen.
+
*插上电源后,可以在屏幕上随意画出任何图案或线条。
 
[[File:IM140714002in2.gif|400px]]
 
[[File:IM140714002in2.gif|400px]]
  

Revision as of 01:48, 9 August 2014

概述

IM140714002 5.jpg

ITDB02-2.4S 是一个2.4inch SPI接口的TFT LCD模块,分辨率为320X240,262K种颜色。LCD模块的控制芯片为ILI9341V,它的接口是SPI的,需要6根线(SCK,MISO,MOSI,CS,D/C,RST)来控制。而且,这个模块还包含了micro SD卡接口,带触摸功能。

购买 ITDB02-2.4S (SKU:IM140714002)

特点

  • 兼容3.3/5V操作电平
  • 自带micro SD卡接口
  • 支持用IO口或PWM来控制背光
  • 触摸屏

规格

PCB尺寸 44mm X 74mm X 1.6mm
电源 5V DC
驱动IC ILI9341V
分辨率 320*240

电气特性

参数 最小值 经典值 最大值 单位
电源 4.5 5 5.5 VDC
最高输入电压 (Target Voltage = 3.3V) 3 3.3 3.6 V
最高输入电压 (Target Voltage = 5V) 4.5 5 5.5 V
最低输入电压 -0.3 0 0.5 V
电流 - 40 80 mA

硬件图

IM140714002pic1.jpg IM140714002pic2.jpg IM140714002pic3.jpg

Pin Map

引脚 类型* 描述
VCC P 5V Power supply pin
GND G Ground
SCK I SPI SCK
MISO O SPI MISO
MOSI I SPI MOSI
CS I Chip Select for TFT
D/C I Command or parameter select
RST I RESET signal for TFT
LEDA* I Backlight control pin
SD_CS I Chip Select for SD
T_CS I Chip Select for touch function
T_IRQ O Interrupt output for touch
  • 类型: P:电源; G:地; I:输入; O:输出.
  • LEDA: 当LEDA设置为高电平,背光会亮;当LEDA设置为低电平,背光会熄灭。

使用指南

1.触摸功能

  • 2_4_spi_touch.ino 烧写进 UNO 主板
File:2_4_spi_touch.zip
  • 然后按照以下的接线方式连接UNO和ITDB02-2.4S模块:
2.4S pins UNO pins
VCC 5V
GND GND
SCK D13
MISO D12
MOSI D11
CS D10
D/C D9
RST D8
LEDA 5V/3V3
SD_CS D4
T_CS D2
T_IRQ D3
  • 插上电源后,可以在屏幕上随意画出任何图案或线条。

IM140714002in2.gif

2.Display the image from micro SD card

  • Download the library from this link: https://github.com/adafruit/Adafruit_ILI9340 , then extract it into the directory \arduino\libraries
  • Copy the image woof.bmp from the directory Adafruit_ILI9340\examples\spitftbitmap to your SD card, then plug the card into the SD card slot on ITDB02-2.2S LCD module
  • Use arduino IDE to open spitftbitmap.ino in the directory Adafruit_ILI9340\examples\spitftbitmap then upload it to UNO main board.
  • Select 5V electronic level in the 2.2S LCD module, then use dupont lines to connect UNO and LCD module according to the table as below:
2.4S pins UNO pins
VCC 5V
GND GND
SCK D13
MISO D12
MOSI D11
CS D10
D/C D9
RST D8
LEDA 5V/3V3
SD_CS D4
  • Power UNO main board, a picture of dog showed on the display.

Download

Specification for TFT LCD module--File:H24TM84A-spec.pdf

Schematic--File:IM140714002-ITDB02-2.4S-schematic.pdf

Useful Link

https://github.com/adafruit/Adafruit_ILI9340