ITDB02-2.4S

From ITEAD Wiki
Revision as of 08:10, 22 July 2014 by ITead (Talk | contribs)

Jump to: navigation, search

Overview

IM140714002 5.jpg

ITDB02-2.4S module is 2.4" SPI TFT LCD with 262K color 320 x 240 resolutions. The controller chip of this LCD module is ILI9341V. Since its interface is SPI, you need 6 Dupont lines (SCK,MISO,MOSI,CS,D/C,RST) to control the LCD module. Moreover, there is an on-board micro SD card slot for multimedia storage and data logging purposes. This 2.4" LCD is a resistive touchscreen as well, so you can detect finger presses anywhere on the screen.

Features

  • Compatible for 3.3/5V operating level
  • Integrated with an micro SD card slot
  • Support IO/PMW to control the backlight
  • Resistive touchscreen

Specification

PCB size 44mm X 74mm X 1.6mm
Power supply 5V DC
Driver IC ILI9341V
Resolution 320*240

Electronic Characteristics

Parameter Min. Typical Max. Unit
Power supply 4.5 5 5.5 VDC
Input voltage VinH (Target Voltage = 3.3V) 3 3.3 3.6 V
Input voltage VinH (Target Voltage = 5V) 4.5 5 5.5 V
Input voltage VinL -0.3 0 0.5 V
Current Consumption - 40 80 mA

Hardware

IM140714002pic1.jpg IM140714002pic2.jpg IM140714002pic3.jpg

Pin Map

Pin Type* Description
VCC P 5V Power supply pin
GND G Ground
SCK I SPI SCK
MISO O SPI MISO
MOSI I SPI MOSI
CS I Chip Select for TFT
D/C I Command or parameter select
RST I RESET signal for TFT
LEDA* I Backlight control pin
SD_CS I Chip Select for SD
T_CS I Chip Select for touch function
T_IRQ O Interrupt output for touch
  • Type: P--Power supply; G--Ground; I--Input; O--Output.
  • LEDA: When LEDA is set as high electronic level, the backlight turns on. When it's set as low electronic level, the backlight turns off.

Instruction

1.Touch Function

  • Upload 2_4_spi_touch.ino into UNO main board
  • Connect ITDB02-2.4S module to UNO according to the table as below:
2.2S pins UNO pins
VCC 5V
GND GND
SCK D13
MISO D12
MOSI D11
CS D10
D/C D9
RST D8
LEDA 5V/3V3
SD_CS D4
T_CS D2
T_IRQ D3
  • Power UNO mainboard, you can start to draw any line or pattern on the screen.

IM140714002in2.gif

2.Display the image from micro SD card

  • Download the library from this link: https://github.com/adafruit/Adafruit_ILI9340 , then extract it into the directory \arduino\libraries
  • Copy the image woof.bmp from the directory Adafruit_ILI9340\examples\spitftbitmap to your SD card, then plug the card into the SD card slot on ITDB02-2.2S LCD module
  • Use arduino IDE to open spitftbitmap.ino in the directory Adafruit_ILI9340\examples\spitftbitmap then upload it to UNO main board.
  • Select 5V electronic level in the 2.2S LCD module, then use dupont lines to connect UNO and LCD module according to the table as below:
2.2S pins UNO pins
VCC 5V
GND GND
SCK D13
MISO D12
MOSI D11
CS D10
D/C D9
RST D8
LEDA 5V/3V3
SD_CS D4

Download

Specification for TFT LCD module--File:H24TM84A-spec.pdf

Schematic--File:IM140714002-ITDB02-2.4S-schematic.pdf

Useful Link

https://github.com/adafruit/Adafruit_ILI9340