Difference between revisions of "ITDB02-2.2S"

From ITEAD Wiki
Jump to: navigation, search
m (Instruction)
m (Overview)
Line 2: Line 2:
 
[[File:IM140714001_6.jpg|thumb|400px|right]]
 
[[File:IM140714001_6.jpg|thumb|400px|right]]
 
ITDB02-2.2S module is 2.2" SPI TFT LCD with 262K color 320 x 240 resolutions. The controller chip of this LCD module is ILI9341, providing different pin-saving SPI communication without sacrificing the data transmitting speed. Since its interface is SPI, you need 6 Dupont lines (SCK,MISO,MOSI,CS,D/C,RST) to control this LCD module. Moreover, this module integrates an SD card slot.
 
ITDB02-2.2S module is 2.2" SPI TFT LCD with 262K color 320 x 240 resolutions. The controller chip of this LCD module is ILI9341, providing different pin-saving SPI communication without sacrificing the data transmitting speed. Since its interface is SPI, you need 6 Dupont lines (SCK,MISO,MOSI,CS,D/C,RST) to control this LCD module. Moreover, this module integrates an SD card slot.
 +
 +
Go to shopping [http://imall.iteadstudio.com/im140714001.html ITDB02-2.2S]
  
 
==Features==  
 
==Features==  

Revision as of 02:19, 21 July 2014

Overview

IM140714001 6.jpg

ITDB02-2.2S module is 2.2" SPI TFT LCD with 262K color 320 x 240 resolutions. The controller chip of this LCD module is ILI9341, providing different pin-saving SPI communication without sacrificing the data transmitting speed. Since its interface is SPI, you need 6 Dupont lines (SCK,MISO,MOSI,CS,D/C,RST) to control this LCD module. Moreover, this module integrates an SD card slot.

Go to shopping ITDB02-2.2S

Features

  • Compatible to 3.3/5V operating level
  • Integrated with an micro SD card slot
  • Support IO/PMW to control the backlight


Specifications

PCB size 41mm X 68mm X 1.6mm
Power supply 5V DC
Driver IC ILI9341
Resolution 320*240
LED numbers 4LEDs

Electrical Characteristics

Parameter Min. Typical Max. Unit
Power voltage 4.5 5 5.5 VDC
Input voltage VinH (Target Voltage = 3.3V) 3 3.3 3.6 V
Input voltage VinH (Target Voltage = 5V) 4.5 5 5.5 V
Input voltage VinL -0.3 0 0.5 V
Current Consumption - 40 80 mA

Hardware

IM140714001pic1.jpg IM140714001pic2.jpg IM140714001pic3.jpg

Pin Map

Pin Type* Description
VCC P 5V Power supply pin
GND G Ground
SCK I SPI SCK
MISO O SPI MISO
MOSI I SPI MOSI
CS I Chip Select for TFT
D/C I Command or parameter select
RST I RESET signal for TFT
LEDA* I Backlight control pin
SD_CS I Chip Select for SD
  • Type: P--Power supply; G--Ground; I--Input; O--Output.
  • LEDA: When LEDA is set as high electronic level, the backlight turns on. When it's set as low electronic level, the backlight turns off.

Instruction

Display the image from micro SD card

  • copy the image woof.bmp from the directory Adafruit_ILI9340\examples\spitftbitmap to your SD card, then plug the card into the SD card slot on ITDB02-2.2S LCD module
  • Use arduino IDE to open spitftbitmap.ino in the directory Adafruit_ILI9340\examples\spitftbitmap then upload it to UNO main board. Select 5V electronic level in the 2.2S LCD module, then use dupont lines to connect UNO and LCD module according to the table as below:
2.2S pins UNO pins
VCC 5V
GND GND
SCK D13
MISO D12
MOSI D11
CS D10
D/C D9
RST D8
LEDA 5V/3V3
SD_CS D4
  • Power UNO main board, a picture of dog showed on the display.

Control LEDA backlight via PWM pins

  • Use arduino IDE to open the demo 0.1Basics\Fade, then upload it into UNO
  • Connect ITDB02-2.2S module to UNO according to the table as below:
2.2S pins UNO pins
VCC 5V
GND GND
LEDA D9
  • Power UNO main board, you will see the backlight of display turn form dark to light circularly.

IM140714001in2.gif

Download

Schematic--File:sch_ITDB02-2.2S.pdf

Useful Link

https://github.com/adafruit/Adafruit_ILI9340