Difference between revisions of "IR Shield/zh-cn"

From ITEAD Wiki
Jump to: navigation, search
m
(Created page with "==相关链接== http://blog.iteadstudio.com/diy-intelligent-monitor-for-home-temperature-and-humidity/")
 
(8 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
==概述==
 
==概述==
 
[[File:IM140715001_4.jpg|thumb|400px|right]]
 
[[File:IM140715001_4.jpg|thumb|400px|right]]
IR Shield是一块Arduino主板的扩展板,它带有红外收发模块,nRF24L01接口,XBee接口,MicroSD卡接口和温湿度传感器。有了它,你就可以监控室内的温湿度和控制红外的设备(空调,电视等等),使你的家变得更加智能化。
+
[[IR Shield]]是一块Arduino主板的扩展板,它带有红外收发模块,nRF24L01接口,XBee接口,MicroSD卡接口和温湿度传感器。有了它,你就可以监控室内的温湿度和控制红外的设备(空调,电视等等),使你的家变得更加智能化。
  
Go shopping
+
购买
  
==Features==
+
==特点==
*Compatible for 5/3.3V main board
+
*兼容5/3.3V主板
*Micro SD card slot
+
*micro SD卡接口
*Xbee interface
+
*XBee 接口
  
==Specification==
+
==规格==
 
{| border="1"
 
{| border="1"
| PCB size||55.88mm X 68.58mm X 1.6mm
+
| PCB 尺寸||55.88mm X 68.58mm X 1.6mm
 
|-
 
|-
| Power supply||5V DC
+
| 电源||5V DC
 
|-
 
|-
| Indicators||PWR,LED1,LED2
+
| 指示灯||PWR,LED1,LED2
 
|-  
 
|-  
| Communication Protocol||UART,IIC,SPI
+
| 接口||UART,IIC,SPI
 
|-
 
|-
 
|}
 
|}
  
==Electrical Characteristics==
+
==电气特性==
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
| align="center" style="background:#f0f0f0;"|'''Parameter'''
+
| align="center" style="background:#f0f0f0;"|'''参数'''
| align="center" style="background:#f0f0f0;"|'''Min.'''
+
| align="center" style="background:#f0f0f0;"|'''最小值'''
| align="center" style="background:#f0f0f0;"|'''Typical'''
+
| align="center" style="background:#f0f0f0;"|'''经典值'''
| align="center" style="background:#f0f0f0;"|'''Max.'''
+
| align="center" style="background:#f0f0f0;"|'''最大值'''
| align="center" style="background:#f0f0f0;"|'''Unit'''
+
| align="center" style="background:#f0f0f0;"|'''单位'''
 
|-
 
|-
| Power voltage||4.5||5||5.5||VDC
+
| 电源||4.5||5||5.5||VDC
 
|-
 
|-
| Input voltage VinH (Target Voltage = 3.3V)||3||3.3||3.6||V
+
| 最高输入电压 (Target Voltage = 3.3V)||3||3.3||3.6||V
 
|-
 
|-
| Input voltage VinH (Target Voltage = 5V)||4.5||5||5.5||V
+
| 最高输入电压 (Target Voltage = 5V)||4.5||5||5.5||V
 
|-
 
|-
| Input voltage VinL||-0.3||0||0.5||V
+
| 最低输入电压||-0.3||0||0.5||V
 
|-
 
|-
| Current Consumption||-||40||-||mA
+
| 电流||-||40||-||mA
 
|}
 
|}
  
==Hardware==
+
==硬件图==
 
[[File:IM140715001pic1.jpg|500px]]
 
[[File:IM140715001pic1.jpg|500px]]
 
[[File:IM140715001pic2.jpg|500px]]
 
[[File:IM140715001pic2.jpg|500px]]
Line 50: Line 50:
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
| align="center" style="background:#f0f0f0;"|'''Arduino Pin'''
+
| align="center" style="background:#f0f0f0;"|'''Arduino引脚'''
| align="center" style="background:#f0f0f0;"|'''Description'''
+
| align="center" style="background:#f0f0f0;"|'''描述'''
 
|-
 
|-
 
| D0||XBEE_TX
 
| D0||XBEE_TX
Line 94: Line 94:
 
|-
 
|-
 
|}
 
|}
*IR_TX: when D3 is set as high level switch, IR Diode will emit signals out. When D3 is set as low level switch, IR Diode won’t work.
+
*IR_TX: 当D3设置为高电平,红外发射管会向外发射信号;当D3设置为低电平,红外发射管不工作。
*IR_RX: Use HS0038B as IR receiving module
+
*Jumpers:
+
:Jumpers can directly connect to Arduino’s IO. If you don’t need them or their corresponding pins are occupied, you can remove the jumpers.
+
:*A0: insert a 10K resistance to A0 button
+
:*LED1: connect to D6 pin. If the output voltage is high, LED1 turns on.
+
:*LED2: connect to D7 pin. If the output voltage is high, LED1 turns on.
+
*Switch: Set the switch level according to Arduino main board. When the mainboard is set in 5V, you should turn the switch to 5V; when in 3.3V, you should turn to 3.3V.
+
  
==Instruction==
+
*IR_RX: 使用HS0038B作为IR接收模块。
Please refer to our blogs:
+
 
 +
*Jumpers:跳线帽是直接连接到Arduino的IO 上,如果不需要或引脚被其他模块占用时,请移除其跳线帽。
 +
 
 +
:A0:上拉一个10K电阻到A0按钮上。
 +
 
 +
:LED1:连接到D6引脚,置高时LED1会亮。
 +
 
 +
:LED2:连接到D7引脚,置高时LED2会亮。
 +
 
 +
*Switch:根据Arduino主板的操作电平来设置,当主板工作在5V,开关打到5V;当主板工作在3.3V,开关打到3V3。
 +
 
 +
==使用指南==
 +
请参看博文:
  
 
http://blog.iteadstudio.com/diy-intelligent-monitor-for-home-temperature-and-humidity/
 
http://blog.iteadstudio.com/diy-intelligent-monitor-for-home-temperature-and-humidity/
  
==Download==
+
==文件下载==
*Schematic--[[:File:IM140715001-IR Shield-schematic.pdf]]
+
*原理图--[[:File:IM140715001-IR Shield-schematic.pdf]]
*IR Receiver Datasheet--[[:File:IM140715001-HS0038B.pdf]]
+
*IR Receiver数据--[[:File:IM140715001-HS0038B.pdf]]
*SHT1x Datasheet--[[:File:SHT1x_Datasheet.pdf]]
+
*SHT1x 数据--[[:File:SHT1x_Datasheet.pdf]]
 
*Temperature & Humidity sensor demo--[[:File:Sht10.zip]]
 
*Temperature & Humidity sensor demo--[[:File:Sht10.zip]]
  
==Useful Link==
+
==相关链接==
 
http://blog.iteadstudio.com/diy-intelligent-monitor-for-home-temperature-and-humidity/
 
http://blog.iteadstudio.com/diy-intelligent-monitor-for-home-temperature-and-humidity/

Latest revision as of 02:46, 9 August 2014

概述

IM140715001 4.jpg

IR Shield是一块Arduino主板的扩展板,它带有红外收发模块,nRF24L01接口,XBee接口,MicroSD卡接口和温湿度传感器。有了它,你就可以监控室内的温湿度和控制红外的设备(空调,电视等等),使你的家变得更加智能化。

购买

特点

  • 兼容5/3.3V主板
  • micro SD卡接口
  • XBee 接口

规格

PCB 尺寸 55.88mm X 68.58mm X 1.6mm
电源 5V DC
指示灯 PWR,LED1,LED2
接口 UART,IIC,SPI

电气特性

参数 最小值 经典值 最大值 单位
电源 4.5 5 5.5 VDC
最高输入电压 (Target Voltage = 3.3V) 3 3.3 3.6 V
最高输入电压 (Target Voltage = 5V) 4.5 5 5.5 V
最低输入电压 -0.3 0 0.5 V
电流 - 40 - mA

硬件图

IM140715001pic1.jpg IM140715001pic2.jpg IM140715001pic3.jpg

Pin Map

Arduino引脚 描述
D0 XBEE_TX
D1 XBEE_RX
D2 nRF24L01_IRQ & STD Button
D3 IR_TX*
D4 SD_CS
D5 IR_RX*
D6 LED1*
D7 LED2*
D8 -
D9 nRF24L01_CE
D10 nRF24L01_CS
D11 MOSI
D12 MISO
D13 SCK
A0 A0 Button
A1 -
A2 -
A3 -
A4 SHT10_SDA
A5 SHT10_SCL
  • IR_TX: 当D3设置为高电平,红外发射管会向外发射信号;当D3设置为低电平,红外发射管不工作。
  • IR_RX: 使用HS0038B作为IR接收模块。
  • Jumpers:跳线帽是直接连接到Arduino的IO 上,如果不需要或引脚被其他模块占用时,请移除其跳线帽。
A0:上拉一个10K电阻到A0按钮上。
LED1:连接到D6引脚,置高时LED1会亮。
LED2:连接到D7引脚,置高时LED2会亮。
  • Switch:根据Arduino主板的操作电平来设置,当主板工作在5V,开关打到5V;当主板工作在3.3V,开关打到3V3。

使用指南

请参看博文:

http://blog.iteadstudio.com/diy-intelligent-monitor-for-home-temperature-and-humidity/

文件下载

相关链接

http://blog.iteadstudio.com/diy-intelligent-monitor-for-home-temperature-and-humidity/