Gboard 800

From ITEAD Wiki
Revision as of 03:47, 10 January 2015 by ITead (Talk | contribs)

Jump to: navigation, search

Overview

IM141125007 4.jpg

Gboard 800 is a unique Arduino board which features a SIM800 GSM/GPRS/BT module, an XBee socket, nRF24L01+ module interface and an ATMega328P controller. This board can be added wireless XBee / nRF24L01+ control as well as GSM/GPRS connectivity to your projects. It’s great for anything from home automation to robot control. The possibilities are endless!

Gboard 800 can be used as a GSM/GPRS data transfer or wireless communication project development platform. Gboard supports wide range power supply and Micro SD for mass storage. There are some 3pin electronic brick/ sensor brick interface breakout on board, which offers an easy way for a quick prototyping. The board requires FTDI basic board to upload sketch, you can use our Foca board to do it.

Note:

  1. Gboard 800 has a micro USB connector only for debugging or firmware uploading.
  2. When you upload sketch to Gboard, please choose the board Arduino Duemilanove w/ ATmega328.
  3. The bootloarder file is ATmegaBOOT_168_atmega328.hex, you can find it in the directory arduino\hardware\arduino\bootloaders\atmega
  4. The serial interface (bootloader connection) is 3.3v, not the typical 5v as on many Arduino boards - anyone using an alternative to the Foca board must take note not to risk damage.

Specification

PCB size 88.1mm X 60.7mm X 1.6mm
Power supply 7-23V DC
Microprocessor Atmega328
Indicators PWR, Status, NET
RoHS Yes

Electrical Characteristics

Specification Min. Typical Value Max. Unit
Power Voltage 7 - 23 VDC
Input Voltage VH (Target Voltage = 3.3V) 3 3.3 3.6 V
Input Voltage VL: -0.3 0 0.5 V
Current Consumption - 100 500 mA

Hardware

IM141125007 - Gboard 800 - dimension.jpg IM141125007pic2.jpg

Note:

  • Baterry Socket: you can connect a Li-ion battery onto the socket to power the board up instead of DC external power supply, the input voltage is from 3.4V~4.4V.
  • Debug Port: it is a debugging interface for SIM800 so that you can upgrade firmware and debug software.

Pin Map

  • Nrf24L01 Socket
Index of Interface Name of Interface Index of Arduino
1 GND -
2 3V3
3 CE D8
4 CS D9
5 SCK D13
6 MOSI D11
7 MISO D12
8 IRQ -
  • SD Card Socket
Index of Interface Name of Interface Index of Arduino
1 SD_CS D10
2 SD_MOSI D11
3 3V3 -
4 SD_SCK D13
5 GND -
6 SD_MISO D12

UART Setting Jumpers

The SIM800 module and XBee module communicate to Atmega 328 through UART. Because they could not communicate in same port in the same time, there are two UART setting jumpers to configure the UART communication. The figure of UART setting jumpers is as below.

GBoard4.jpg

(Figure of UART setting jumpers)

D0 and D1 are hardware UART ports of Arduino. D2 and D3 are digital GPIO of Arduino. There are two configurations to set the UART communication.

Description UART Setting Jumpers Connection Figure
Hardware UART to SIM900,

Software UART to Specific

ST – D0(Hardware Rx of Arduino)

SR – D1(Hardware Tx of Arduino)

XT – D2(Software Rx/Tx of Arduino)

XR – D3(Software Rx/Tx of Arduino)

GBoard5.jpg
Software UART to SIM900,

Hardware UART to Specific

XT – D0(Hardware Rx of Arduino)

XR – D1(Hardware Tx of Arduino)

ST – D2(Software Rx/Tx of Arduino)

SR – D3(Software Rx/Tx of Arduino)

GBoard6.jpg

ST: UART Tx of SIM900 module

SR: UART Rx of SIM900 module

XT: XBee Tx of XBee module

XR: XBee Rx of XBee module

Power and reset connection of SIM800

In the GBoard, the PWRKEY and RESET pins of SIM800 module connect to Arduino as list below.

Arduino pin SIM800 pin Enable
D6 PWR High level Active
D7 RESET High level Active

Revision History

Rev. Description Release date
v1.0 Initial version 2014-12-10

Download

Tools: