ITEAD8285

Overview

The ITEAD8285 is an ultra low-power Wi-Fi module designed by ITEAD. The module adopts the highly integrated Wi-Fi chip ESP8285. It features industry's highly competitive packaging size and ultra-low power technology. Specially designed for mobile devices and the Internet of Things application, it connects physical devices to Wi-Fi wireless network to make Internet or LAN communications.

ITEAD8285 has completed self-contained wireless network, with built-in 32-bit kernel processor, on-chip SRAM, it can be used as the main control chip, but also as a WiFi adapter. To apply it to other microcontroller-based designs, simply by using SPI/SDIO or I2C/UART interface communication.

The module supports IPEX connector and stamp hole interface. It can be widely apply for smart power grid, smart transportation, smart home, handheld devices, industrial control, etc.

Go shopping ITEAD8285 WiFi Wireless Module (SKU:)

Features

• 802.11 b/g/n/d/e/i/k/r

• Support STA/AP/STA+AP mode

• WPA/WPA2 PSK and WP

• Built-in TCP/IP protocol stack, support multi-way TCP Client connection

• Support rich Socket AT commands

• Support UART/GPIO data communication interface

• Built-in 32 bit MCU, also work as application processor

• 3.3V single supply

• Wi-Fi Direct (P2P) support

• Support MIMO 1×1 and 2×1, STBC, A- MPDU and A-MSDU aggregation and 0.4μs guard interval

• WMM power save U-APSD

• Multiple queue management to fully utilize traffic prioritization defined by 802.11e standard.

• Adaptive rate fallback algorithm sets the optimum transmission rate and Tx power based on actual SNR and packet loss information.

Main Technical Specifications

Module	Type	ITEAD8285
	Chip	ESP8285
Wi-Fi	Wireless Standard	IEEE 802.11b/g/n/d/e/i/k/r
	Frequency Range	2.412GHz-2.484GHz
	Tx Power	802.11b: +20 +/-2dBm (@11Mbps)
		802.11g: +17 +/-2dBm (@54Mbps)
		802.11n: +14 +/-2dBm (@HT20, MCS7)
	Rx Sensitivity	802.11b: -91 dBm (@11Mbps ,CCK)
		802.11g: -75 dBm (@54Mbps, OFDM)
		802.11n: -72 dBm (MCS7)
	Connector	External：stamp hole interface
		External：I-PEX connector
Hardware	Peripheral Interface	UART，IIC，PWM，GPIO，ADC
	Operating Voltage	3.3V
	GPIO Drive capability	Max：12mA
	Operating Current	Continue sending=>Average value：~70mA, Peak value: 200mA Normal mode=> Average value: ~12mA, Peak value: 200mA Standby：<200uA
	Operating Temperature Range	-40℃~125℃
	Storage Temperature Range	Temp.：<40℃, Relative humidity：<90%R.H.
	Size	13.5mm*13.7mm*1mm；
Serial transparent transmission	Transmission rate	110-921600bps
	TCP Client	5
Software	Wireless network types	STA/AP/STA+AP
	Security	WEP/WPA-PSK/WPA2-PSK
	Encryption	WEP64/WEP128/TKIP/AES
	Firmware Upgrade	UART Download / OTA (via network)
	Network Protocols	IPv4, TCP/UDP/FTP/HTTP

Hardware

ITEAD8285 has many interfaces, supports UART, IIC, PWM, GPIO, ADC, etc., suitable for a variety of networking applications.

Pin Definitions

PIN	Function	Description
1	ANT	WiFi Antenna
2	ADC	ADC, input range: 0V-1V；
3	EN	Chip enable terminal. Active high: chip works normally; Active low: chip close, very small current.
4	GPIO16	GPIO16
5	GPIO14	GPIO14; HSPI_CLK
6	GPIO12	GPIO12; HSPI_MISO
7	GPIO13	GPIO13; HSPI_MOSI; UART0_CTS
8	GPIO15	GPIO15; HSPI_CS; UART0_RTS
9	GPIO2	Also used as a programming flash UART1_TX；GPIO2
10	GPIO0	GPIO0; SPI_CS2
11	GPIO4	GPIO4
12	GND	GND
13	GPIO9	PIHD；HSPIHD；GPIO9
14	GPIO10	SPIWP；HSPIWP；GPIO10
15	GPIO11	SPI_CS0；GPIO11
16	GPIO6	SPI_CLK；GPIO6
17	GPIO7	SPI_MSIO；GPIO7
18	GPIO8	SPI_MOSI；GPIO8
19	GPIO5	GPIO5
20	GND	GND
21	RX	Also used as a programming flash UART Rx；GPIO3
22	TX	Also used as a programming flash UART Tx ；GPIO1；SPI_CS1
23	3V3	Power supply
24	RESET	External reset（low active）