Iteaduino DUE

Overview

Iteaduino DUE is a microcontroller board based on the Atmel SAM3X8E ARM Crotex-M3 core. It is the improvement board based on the Arduino DUE. It has 54 digital IO pins, 12 analog inputs, 4 UARTs, a 84MHz clock, an USB OTG capable connection, 2 DACs, 2 IIC, a power jack, an SPI header, a reset button and an erase button.

Warning: Unlike other Iteadduino boards, the Iteaduino Due board runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Providing higher voltages, like 5V to an I/O pin could damage the board.

The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with a AC-to-DC adapter or battery to get started. The Due is compatible with all Arduino compatible shields that work at 3.3V and are compliant with the 1.0 Arduino compatible pinout.

The Due follows the 1.0 pinout:

TWI: SDA and SCL pins that are near to the AREF pin.

The IOREF pin which allows an attached shield with the proper configuration to adapt to the voltage provided by the board. This enables shield compatibility with a 3.3V board like the Due and AVR-based boards which operate at 5V. An unconnected pin, reserved for future use.

ARM Core benefits

The Due has a 32-bit ARM core that can outperform typical 8-bit microcontroller boards. The most significant differences are:

A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock.

CPU Clock at 84Mhz.

96 KBytes of SRAM.

512 KBytes of Flash memory for code.

A DMA controller, that can relieve the CPU from doing memory intensive tasks.

Spec

Microcontroller	AT91SAM3X8E
Operating Voltage	3.3V
POWER Supply Voltage(recommanded)	7~24V
Power supply Max Voltage	26V
Digital IO pins	54(of which 12 provide PWM output)
Analog Input pins(ADC)	12
Analog Output pins(DAC)	2
Total DC Output current on all IO lines	130mA
DC current of 3.3V	800mA
DC current of 5V	800mA
Flash Memory	512KB all available for user application
SRAM	96KB(2 banks:64KB and 32KB)
Clock frequency	84MHz

Hardware top view

Pin map

Due Pin Number	SAM3X Pin Name	Mapped Pin Name
0	PA8	RX0
1	PA9	TX0
2	PB25	Digital Pin 2
3	PC28	Digital Pin 3
4	connected to both PA29 and PC26	Digital Pin 4
5	PC25	Digital Pin 5
6	PC24	Digital Pin 6
7	PC23	Digital Pin 7
8	PC22	Digital Pin 8
9	PC21	Digital Pin 9
10	connected to both PA28 and PC29	Digital Pin 10
11	PD7	Digital Pin 11
12	PD8	Digital Pin 12
13	PB27	Digital Pin 13 / Amber LED "L"
14	PD4	TX3
15	PD5	RX3
16	PA13	TX2
17	PA12	RX2
18	PA11	TX1
19	PA10	RX1
20	PB12	SDA
21	PB13	SCL
22	PB26	Digital Pin 22
23	PA14	Digital Pin 23
24	PA15	Digital Pin 24
25	PD0	Digital Pin 25
26	PD1	Digital Pin 26
27	PD2	Digital Pin 27
28	PD3	Digital Pin 28
29	PD6	Digital Pin 29
30	PD9	Digital Pin 30
31	PA7	Digital Pin 31
32	PD10	Digital Pin 32
33	PC1	Digital Pin 33
34	PC2	Digital Pin 34
35	PC3	Digital Pin 35
36	PC4	Digital Pin 36
37	PC5	Digital Pin 37
38	PC6	Digital Pin 38
39	PC7	Digital Pin 39
40	PC8	Digital Pin 40
41	PC9	Digital Pin 41
42	PA19	Digital Pin 42
43	PA20	Digital Pin 43
44	PC19	Digital Pin 44
45	PC18	Digital Pin 45
46	PC17	Digital Pin 46
47	PC16	Digital Pin 47
48	PC15	Digital Pin 48
49	PC14	Digital Pin 49
50	PC13	Digital Pin 50
51	PC12	Digital Pin 51
52	PB21	Digital Pin 52
53	PB14	Digital Pin 53
54	PA16	Analog In 0
55	PA24	Analog In 1
56	PA23	Analog In 2
57	PA22	Analog In 3
58	PA6	Analog In 4
59	PA4	Analog In 5
60	PA3	Analog In 6
61	PA2	Analog In 7
62	PB17	Analog In 8
63	PB18	Analog In 9
64	PB19	Analog In 10
65	PB20	Analog In 11
66	PB15	DAC0
67	PB16	DAC1
68	PA1	CANRX
69	PA0	CANTX
70	PA17	SDA1
71	PA18	SCL2
72	PC30	LED "RX"
73	PA21	LED "TX"
74	PA25	(MISO)
75	PA26	(MOSI)
76	PA27	(SCLK)
77	PA28	(NPCS0)
78	PB23	(unconnected)
USB	PB11	ID
USB	PB10	VBOF

Power

Iteaduino Due can be powered via the USB connector or with an external power supply. The power source is selected automatically.

External (non-USB) power can come either from an AC-to-DC adapter (wall-wart) or battery. The adapter can be connected by plugging a 2.1mm center-positive plug into the board's power jack. Leads from a battery can be inserted in the GND and Vin pin headers of the POWER connector.

The board can operate on an external supply of 7 to 24 volts. If supplied with less than 7V, however, the 5V pin may supply less than five volts and the board may be unstable.

The power pins are as follows:

• VIN. The input voltage to the Iteaduino board when it's using an external power source (as opposed to 5 volts from the USB connection or other regulated power source). You can supply voltage through this pin, or if supplying voltage via the power jack, access it through this pin.

• 5V. This pin outputs a regulated 5V from the regulator on the board. The board can be supplied with power either from the DC power jack (7 - 24V), the USB connector (5V), or the VIN pin of the board (7-24V). Supplying voltage via the 5V or 3.3V pins bypasses the regulator, and can damage your board. We don't advise it.

• 3.3V. A 3.3 volt supply generated by the on-board regulator. Maximum current draw is 800 mA. This regulator also provides the power supply to the SAM3X microcontroller.

• GND. Ground pins.

• IOREF. This pin on the Arduino board provides the voltage reference with which the microcontroller operates. A properly configured shield can read the IOREF pin voltage and select the appropriate power source or enable voltage translators on the outputs for working with the 5V or 3.3V.

Memory

The SAM3X has 512 KB (2 blocks of 256 KB) of flash memory for storing code. The bootloader is preburned in factory from Atmel and is stored in a dedicated ROM memory. The available SRAM is 96 KB in two contiguous bank of 64 KB and 32 KB. All the available memory (Flash, RAM and ROM) can be accessed directly as a flat addressing space.

It is possible to erase the Flash memory of the SAM3X with the onboard erase button. This will remove the currently loaded sketch from the MCU. To erase, press and hold the Erase button for a few seconds while the board is powered.

Input and Output

Digital I/O: pins from 0 to 53

Each of the 54 digital pins on the Due can be used as an input or output, using pinMode(), digitalWrite(), anddigitalRead() functions. They operate at 3.3 volts. Each pin can provide (source) a current of 3 mA or 15 mA, depending on the pin, or receive (sink) a current of 6 mA or 9 mA, depending on the pin. They also have an internal pull-up resistor (disconnected by default) of 100 KOhm. In addition, some pins have specialized functions:

• Serial: 0 (RX) and 1 (TX)
• Serial 1: 19 (RX) and 18 (TX)
• Serial 2: 17 (RX) and 16 (TX)
• Serial 3: 15 (RX) and 14 (TX)

Used to receive (RX) and transmit (TX) TTL serial data (with 3.3 V level). Pins 0 and 1 are connected to the corresponding pins of the ATmega16U2 USB-to-TTL Serial chip.

PWM: Pins 2 to 13

Provide 8-bit PWM output with the analogWrite() function. the resolution of the PWM can be changed with theanalogWriteResolution() function.

SPI: SPI header (ICSP header on other Arduino compatible boards)

These pins support SPI communication using the SPI library. The SPI pins are broken out on the central 6-pin header, which is physically compatible with the compatible Uno board, Itead Leonardo and Iteaduino Mega2560. The SPI header can be used only to communicate with other SPI devices, not for programming the SAM3X with the In-Circuit-Serial-Programming technique. The SPI of the Due has also advanced features that can be used with the Extended SPI methods for Due.

CAN: CANRX and CANTX

These pins support the CAN communication protocol but are not not yet supported by Arduino IDE APIs.

"L" LED: 13

There is a built-in LED connected to digital pin 13. When the pin is HIGH, the LED is on, when the pin is LOW, it's off. It is also possible to dim the LED because the digital pin 13 is also a PWM output.

TWI 2: SDA1 and SCL1.

Support TWI communication using the Wire library.

Analog Inputs: pins from A0 to A11

The Due has 12 analog inputs, each of which can provide 12 bits of resolution (i.e. 4096 different values). By default, the resolution of the readings is set at 10 bits, for compatibility with other Iteaduino boards. It is possible to change the resolution of the ADC with analogReadResolution().

The Due’s analog inputs pins measure from ground to a maximum value of 3.3V. Applying more then 3.3V on the Due’s pins will damage the SAM3X chip. The analogReference() function is ignored on the Due.

The AREF pin is connected to the SAM3X analog reference pin through a resistor bridge. To use the AREF pin, resistorBR1 must be desoldered from the PCB.

DAC1 and DAC2

These pins provides true analog outputs with 12-bits resolution (4096 levels) with the analogWrite() function. These pins can be used to create an audio output using the Audio library.

Other pins on the board:

AREF

Reference voltage for the analog inputs. Used with analogReference().

Reset

Bring this line LOW to reset the microcontroller. Typically used to add a reset button to shields which block the one on the board.

Download

Datasheet for Iteaduino DUE

Schematic for Iteaduino DUE