Overview
ITDB02-2.4S module is 2.4" SPI TFT LCD with 262K color 320 x 240 resolutions. The controller chip of this LCD module is ILI9341V. Since its interface is SPI, you need 6 Dupont lines (SCK,MISO,MOSI,CS,D/C,RST) to control the LCD module. Moreover, there is an on-board micro SD card slot for multimedia storage and data logging purposes. This 2.4" LCD is a resistive touchscreen as well, so you can detect finger presses anywhere on the screen.
Features
- Compatible for 3.3/5V operating level
- Integrated with an micro SD card slot
- Support IO/PMW to control the backlight
- Resistive touchscreen
Specification
PCB size |
44mm X 74mm X 1.6mm
|
Power supply |
5V DC
|
Driver IC |
ILI9341V
|
Resolution |
320*240
|
Electronic Characteristics
Parameter
|
Min.
|
Typical
|
Max.
|
Unit
|
Power supply |
4.5 |
5 |
5.5 |
VDC
|
Input voltage VinH (Target Voltage = 3.3V) |
3 |
3.3 |
3.6 |
V
|
Input voltage VinH (Target Voltage = 5V) |
4.5 |
5 |
5.5 |
V
|
Input voltage VinL |
-0.3 |
0 |
0.5 |
V
|
Current Consumption |
- |
40 |
80 |
mA
|
Hardware
Pin Map
Pin
|
Type*
|
Description
|
VCC |
P |
5V Power supply pin
|
GND |
G |
Ground
|
SCK |
I |
SPI SCK
|
MISO |
O |
SPI MISO
|
MOSI |
I |
SPI MOSI
|
CS |
I |
Chip Select for TFT
|
D/C |
I |
Command or parameter select
|
RST |
I |
RESET signal for TFT
|
LEDA* |
I |
Backlight control pin
|
SD_CS |
I |
Chip Select for SD
|
T_CS |
I |
Chip Select for touch function
|
T_IRQ |
O |
Interrupt output for touch
|
- Type: P--Power supply; G--Ground; I--Input; O--Output.
- LEDA: When LEDA is set as high electronic level, the backlight turns on. When it's set as low electronic level, the backlight turns off.
Instruction
1.Touch Function
- Upload 2_4_spi_touch.ino into UNO main board
- Connect ITDB02-2.4S module to UNO according to the table as below:
2.2S pins
|
UNO pins
|
VCC |
5V
|
GND |
GND
|
SCK |
D13
|
MISO |
D12
|
MOSI |
D11
|
CS |
D10
|
D/C |
D9
|
RST |
D8
|
LEDA |
5V/3V3
|
SD_CS |
D4
|
T_CS |
D2
|
T_IRQ |
D3
|
- Power UNO mainboard, you can start to draw any line or pattern on the screen.
2.Display the image from micro SD card
- Download the library from this link: https://github.com/adafruit/Adafruit_ILI9340 , then extract it into the directory \arduino\libraries
- Copy the image woof.bmp from the directory Adafruit_ILI9340\examples\spitftbitmap to your SD card, then plug the card into the SD card slot on ITDB02-2.2S LCD module
- Use arduino IDE to open spitftbitmap.ino in the directory Adafruit_ILI9340\examples\spitftbitmap then upload it to UNO main board.
- Select 5V electronic level in the 2.2S LCD module, then use dupont lines to connect UNO and LCD module according to the table as below:
2.2S pins
|
UNO pins
|
VCC |
5V
|
GND |
GND
|
SCK |
D13
|
MISO |
D12
|
MOSI |
D11
|
CS |
D10
|
D/C |
D9
|
RST |
D8
|
LEDA |
5V/3V3
|
SD_CS |
D4
|
Download
Specification for TFT LCD module--File:H24TM84A-spec.pdf
Schematic--File:IM140714002-ITDB02-2.4S-schematic.pdf
Useful Link
https://github.com/adafruit/Adafruit_ILI9340