ITDB02-2.2S/zh-cn

概述

ITDB02-2.2S 是一个2.2inch SPI TFT LCD屏幕模块，分辨率为320X240，262K种颜色。LCD模块的控制芯片为ILI9341，它的接口是SPI的，需要6根线（SCK,MISO,MOSI,CS,D/C,RST）来控制。而且，这个模块还包含了micro SD卡接口。

购买 ITDB02-2.2S

特色

• 兼容3.3/5V操作电平
• 自带micro SD卡接口
• 支持IO口或PMW来控制背光

规格

PCB 尺寸	41mm X 68mm X 1.6mm
电源电压	5V DC
控制芯片	ILI9341
分辨率	320*240
LED数目	4 LEDs

电气特性

参数	最小值	经典值	最大值	单位
电源电压	4.5	5	5.5	VDC
最高输入电压 (目标电压 = 3.3V)	3	3.3	3.6	V
最高输入电压 (目标电压 = 5V)	4.5	5	5.5	V
最低输入电压	-0.3	0	0.5	V
消耗电流	-	40	80	mA

硬件图

引脚图

引脚	类型*	描述
VCC	P	5V Power supply pin
GND	G	Ground
SCK	I	SPI SCK
MISO	O	SPI MISO
MOSI	I	SPI MOSI
CS	I	Chip Select for TFT
D/C	I	Command or parameter select
RST	I	RESET signal for TFT
LEDA*	I	Backlight control pin
SD_CS	I	Chip Select for SD

• Type: P--电源; G--地; I--输入; O--输出.
• LEDA: 当LEDA设置为高电平，背光会亮；当LEDA设置为低电平，背光会熄灭。

Instruction

Display the image from micro SD card

• download the library from this link: https://github.com/adafruit/Adafruit_ILI9340 , then extract it into the directory \arduino\libraries

• copy the image woof.bmp from the directory Adafruit_ILI9340\examples\spitftbitmap to your SD card, then plug the card into the SD card slot on ITDB02-2.2S LCD module

• Use arduino IDE to open spitftbitmap.ino in the directory Adafruit_ILI9340\examples\spitftbitmap then upload it to UNO main board. Select 5V electronic level in the 2.2S LCD module, then use dupont lines to connect UNO and LCD module according to the table as below:

2.2S pins	UNO pins
VCC	5V
GND	GND
SCK	D13
MISO	D12
MOSI	D11
CS	D10
D/C	D9
RST	D8
LEDA	5V/3V3
SD_CS	D4

• Power UNO main board, a picture of dog showed on the display.

Control LEDA backlight via PWM pins

• Use arduino IDE to open the demo 0.1Basics\Fade, then upload it into UNO
• Connect ITDB02-2.2S module to UNO according to the table as below:

2.2S pins	UNO pins
VCC	5V
GND	GND
LEDA	D9

• Power UNO main board, you will see the backlight of display turn form dark to light circularly.

Download

Schematic--File:sch_ITDB02-2.2S.pdf

Useful Link

https://github.com/adafruit/Adafruit_ILI9340