Difference between revisions of "ITDB02-3.2S Arduino Shield V1"
(Created page with "==Overview== right ITDB02-3.2S V1 module is 3.2" TFT LCD with 65K color 320 x 240 resolutions. The controller of this LCD module is S...") |
m (→Overview) |
||
Line 2: | Line 2: | ||
[[File:ITDB02-3.2S.jpg|thumb|400px|right]] | [[File:ITDB02-3.2S.jpg|thumb|400px|right]] | ||
− | [[ITDB02-3.2S]] V1 module is 3.2" TFT LCD with 65K color 320 x 240 resolutions. The controller of this LCD module is SSD1289 | + | [[ITDB02-3.2S]] V1 module is 3.2" TFT LCD with 65K color 320 x 240 resolutions. The controller of this LCD module is SSD1289. It supports 16bit data interface with 4 wires control interface. Moreover, this module contains the touch screen and SD card socket. |
[[ITDB02-3.2S]] is supported by UTFT Library. | [[ITDB02-3.2S]] is supported by UTFT Library. |
Revision as of 10:19, 11 January 2017
Contents
Overview
ITDB02-3.2S V1 module is 3.2" TFT LCD with 65K color 320 x 240 resolutions. The controller of this LCD module is SSD1289. It supports 16bit data interface with 4 wires control interface. Moreover, this module contains the touch screen and SD card socket.
ITDB02-3.2S is supported by UTFT Library.
Go shopping ITDB02-3.2S V1 (IM120419005)
Features
- Compatible with UTFT library
- With SD Card Socket
Specifications
Driver IC | SSD1289 |
Backlight | 5LEDs |
Power supply | 3.3V |
Touch Panel | Y |
Touch IC | XPT2046 |
Resolution | 240*320 |
Size | 84mm*57mm |
Electrical Characteristics
Parameter | Min. | Typical | Max. | Unit |
Power voltage | 4.5 | 5 | 5.5 | VDC |
Input voltage VinH (Target Voltage = 3.3V) | 3 | 3.3 | 3.6 | V |
Input voltage VinL | -0.3 | 0 | 0.5 | V |
Current Consumption | - | 20 | 40 | mA |
Hardware
Bottom View
Pin Map
Pin | Type* | Description |
GND | G | Ground |
VCC | P | 5V Power Supply pin |
NC | - | No connection |
RS | I | Data/Command selection |
WR | I | Write signal enable, low active |
RD | I | Read signal enable, low active |
DB8 | I | Data Bus |
DB9 | I | Data Bus |
DB10 | I | Data Bus |
DB11 | I | Data Bus |
DB12 | I | Data Bus |
DB13 | I | Data Bus |
DB14 | I | Data Bus |
DB15 | I | Data Bus |
CS | I | Chip Selection,Low level active |
NC | - | No connection |
LED | P | Backlight |
NC | - | No connection |
DB0 | I | Data Bus |
DB1 | I | Data Bus |
DB2 | I | Data Bus |
DB3 | I | Data Bus |
DB4 | I | Data Bus |
DB5 | I | Data Bus |
DB6 | I | Data Bus |
DB7 | I | Data Bus |
T_CLK | I | Touch clock |
T_CS | I | Touch chip selection |
T_DIN | I | Touch data input |
T_BUSY | O | Touch status |
T_DOUT | O | Touch data output |
T_IRQ | O | Touch interrupt |
SD_SO | O | SD MISO |
SD_SCK | I | SD SCK |
SD_SI | I | SD MOSI |
SD_NSS | I | SD NSS |
NC | - | No connection |
NC | - | No connection |
Type*:P: Power supply; G:Ground; I:Input; O:Output; The ITDB02_3.2 uses the SSD1289 controller , it support 16bit data interface. The touch IC is TSC2046.