NoticeDifference between revisions of "ITDB06"
m (→Overview) |
m (→Features) |
||
| Line 21: | Line 21: | ||
==Features== | ==Features== | ||
| + | *802.11 b/g/n | ||
| + | *WIFI @2.4 GHz，support WPA/WPA2 safe mode | ||
| + | *Small size 11.5mm*11.5mm | ||
| + | *Built-in 10 bit high accuracy ADC | ||
| + | *Built-in TCP/IP protocol stack | ||
| + | *Built-in switch, balun, LNA, power amplifier and matching network | ||
| + | *Built-in PLL, voltage stabilizer and power management components | ||
| + | *802.11b mode + 20 dBm output power | ||
| + | *Support antenna diversity | ||
| + | *10uA deep sleep maintain current, shutdown current is less than 5 uA | ||
| + | *Built-in 32-bit lower power CUP | ||
| + | *SDIO 2.0、SPI、UART | ||
| + | *STBC、1x1 MIMO、2x1 MIMO | ||
| + | *A-MPDU&A-MSDU aggregation and 0.4us guard interval | ||
| + | *Wake-up, connect and transfer data packets in 2 ms | ||
| + | *Standby power consumption: <1.0mW (DTIM3) | ||
| + | *Temp range:-40 ~ 125℃ | ||
| + | |||
==Specification== | ==Specification== | ||
==Electrical Characteristics== | ==Electrical Characteristics== | ||
Revision as of 07:54, 16 March 2016
Contents
Overview
The ITDB06 WiFi Module is a low-cost universal WiFi module that developed and designed by ITEAD. The module integrates industry leading Tensilica L106 ultra-low power 32-bit MCU, 16-bit compact mode, frequency supports 80MHz and 160MHz, supports RTOS, integrates Wi-Fi MAC/ BB/RF/PA/LNA, on-board antenna.
This module supports standard IEEE802.11 b/g/n protocol and complete TCP/IP protocol stack.. It allows users to add Internet of Things (IoT) to devices or to build a separate network controller.
ITDB06 is high performance wireless SOC, it provides maximum usability at the lowest cost, offering unlimited possibilities for adding WiFi functions to other systems.
ITDB06 is a complete and self-contained WiFi network solution that can run independently, it can also be mounted as a slave host MCU operation.
When the module is mounted to application and as the only processor, it can boot directly from the external flash memory. Built-in cache system is provided to increase system performance and reduce memory requirements.
When the wireless network is accessed and undertake WiFi adapter tasks, you can add it to any microcontroller-based design, simply connect SPI/SDIO interface or I2C/UART interface.
The powerful processing and storage capabilities enable it to integrate sensors and other application-specific devices through GPIO, which achieves lowest pre-development and minimal system resources occupation during performing.
This module integrates antenna switch balun and power management converter, thus little external circuitry needed, and the entire solution including the front-end module has reduced the PCB size to a new minimum.
The ITDB06 system leading features include energy saving VoIP quickly switch between sleep/ wake mode, low-power operation self-adaptive radio bias, front-end signal processing capability, troubleshooting and radio systems coexist performance eliminates interference of cellular/Bluetooth/DDR/LVDS/LCD .
Features
- 802.11 b/g/n
- WIFI @2.4 GHz，support WPA/WPA2 safe mode
- Small size 11.5mm*11.5mm
- Built-in 10 bit high accuracy ADC
- Built-in TCP/IP protocol stack
- Built-in switch, balun, LNA, power amplifier and matching network
- Built-in PLL, voltage stabilizer and power management components
- 802.11b mode + 20 dBm output power
- Support antenna diversity
- 10uA deep sleep maintain current, shutdown current is less than 5 uA
- Built-in 32-bit lower power CUP
- SDIO 2.0、SPI、UART
- STBC、1x1 MIMO、2x1 MIMO
- A-MPDU&A-MSDU aggregation and 0.4us guard interval
- Wake-up, connect and transfer data packets in 2 ms
- Standby power consumption: <1.0mW (DTIM3)
- Temp range:-40 ~ 125℃
