Difference between revisions of "Gboard 800"

Revision as of 03:01, 5 May 2015

Overview

Gboard 800 is a unique Arduino board which features a SIM800 GSM/GPRS/BT module, an XBee socket, nRF24L01+ module interface and an ATMega328P controller. This board can be added wireless XBee / nRF24L01+ control as well as GSM/GPRS connectivity to your projects. It’s great for anything from home automation to robot control. The possibilities are endless!

Gboard 800 can be used as a GSM/GPRS data transfer or wireless communication project development platform. Gboard supports wide range power supply and Micro SD for mass storage. There are some 3pin electronic brick/ sensor brick interface breakout on board, which offers an easy way for a quick prototyping. The board requires FTDI basic board to upload sketch, you can use our Foca board to do it.

Note:

1. You can not power Gboard 800 by the micro USB connector, it is only for debugging and uploading firmware to the SIM800 module.
2. When you upload sketch to Gboard 800, please choose the board Arduino Duemilanove w/ ATmega328.
3. The bootloarder file is ATmegaBOOT_168_atmega328.hex, you can find it in the directory arduino\hardware\arduino\bootloaders\atmega
4. The serial interface (bootloader connection) is 3.3v, not the typical 5v as on many Arduino boards - anyone using an alternative to the Foca board must take note not to risk damage.

Go shopping Gboard 800(IM141125007)

Features

• SIM800 is a quad-band GSM/GPRS module that works on frequencies GSM 850MHz, EGSM 900MHz, DCS 1800MHz and PCS 1900MHz.
• SIM800 GPRS multi-slot class 12/ class 10 (optional) and supports the GPRS coding schemes CS-1, CS-2, CS-3 and CS-4.
• One USB port can be used as SIM800 debugging and firmware upgrading
• Support Bluetooth function
• Support XBee and nRF24L01+ wireless control
• Require FTDI basic board to upload sketch

Specification

Electrical Characteristics

Hardware

Note:

• Baterry Socket: you can connect a Li-ion battery onto the socket to power the board up instead of DC external power supply, the input voltage is from 3.4V~4.4V.
• Debug Port: it is a debugging interface for SIM800 so that you can upgrade firmware and debug software.

Pin Map

• Nrf24L01 Socket

• SD Card Socket

UART Setting Jumpers

The SIM800 module and XBee module communicate to Atmega 328 through UART. Because they could not communicate in same port in the same time, there are two UART setting jumpers to configure the UART communication. The figure of UART setting jumpers is as below.

(Figure of UART setting jumpers)

D0 and D1 are hardware UART ports of Arduino. D2 and D3 are digital GPIO of Arduino. There are two configurations to set the UART communication.

Description	UART Setting Jumpers Connection	Figure
Hardware UART to SIM800, Software UART to Specific	ST – D0(Hardware Rx of Arduino) SR – D1(Hardware Tx of Arduino) XT – D2(Software Rx/Tx of Arduino) XR – D3(Software Rx/Tx of Arduino)
Software UART to SIM800, Hardware UART to Specific	XT – D0(Hardware Rx of Arduino) XR – D1(Hardware Tx of Arduino) ST – D2(Software Rx/Tx of Arduino) SR – D3(Software Rx/Tx of Arduino)

ST: UART Tx of SIM800 module

SR: UART Rx of SIM800 module

XT: XBee Tx of XBee module

XR: XBee Rx of XBee module

Power and reset connection of SIM800

In the GBoard, the PWRKEY and RESET pins of SIM800 module connect to Arduino as list below.

Revision History

Download

• File:IM141125007 - Gboard 800 - schematic.pdf
• File:SIM800 Series_Bluetooth_Application Note_V1.01.pdf
• File:sim800_hardware_design_v1.05.pdf
• File:SIM800_Series_AT_Command_Manual_V1.05.pdf

Tools:

• Firmware for SIM800 with Bluetooth
• USB Driver for SIM800
• Tool for Uploading firmware to SIM800

Useful Link

• Gboard 800 Bluetooth Library: https://github.com/itead/ITEADLIB_Arduino_SIMCom