NoticeDifference between revisions of "RDM8800"
(→pinmap) |
(→Download) |
||
| Line 96: | Line 96: | ||
==Download== | ==Download== | ||
| + | [ftp://imall.iteadstudio.com/Modules/IM131218001/DS_IM131218001.pdf Datasheet] | ||
| + | |||
| + | [ftp://imall.iteadstudio.com/Modules/IM131218001/SCH_IM131218001.pdf Schematic] | ||
| + | |||
| + | [ftp://imall.iteadstudio.com/Modules/IM131218001/FW_IM131218001.zip Firmware] | ||
==Useful Links== | ==Useful Links== | ||
Revision as of 02:38, 29 May 2014
Contents
Overview
RDM8800 card reader is a module based on PN532 chip customized for 13.56MHz NFC RFID card, compatible with RDM6300 interface, which can read data directly from the serial interface.
Unlike ordinary RFID modules, RDM8800 integrates LGT8FF8A chip, compatible with Arduino library, thus we can modify the firmware to suit our own needs. Itead Studio also released the source codes of RDM8800 firmware, and users can make secondary development based on it.
Specifications
| PCB size | 38.1mm X 17.78mm X 1.6mm |
| Input voltage | 5V |
| Interface | UART |
| Compatibility | With ISO 14443 Type A protocol |
| With ISO 14443 Type B[1] protocol | |
| Baud rate | 9600 |
[1]: Version 1.0 firmware does not support ISO 14443 Type B at present, which requires users to make secondary development.
Electrical characteristics
| Parameter | Min. | Typical | Max. | Unit |
| Supply voltage | 4.8 | 5 | 5.5 | VDC |
| Consumption current (average) | - | 80 | - | mA |
| Logic input voltage | Vss-0.3 | 3.3 | 5 | VDC |
Hardware
pinmap
| Pin | Pin | Pin name | Description |
| P1 | Pin1 | +5V(DC) | Power input |
| P1 | Pin2 | GND | Ground |
| P1 | Pin3 | NC | Unoccupied |
| P1 | Pin4 | RX(TTL) | UART input |
| P1 | Pin5 | TX(TTL) | UART output |
| P2 | Pin1 | LED | Interrupt pin |
| P2 | Pin2 | +5V(DC) | Power output |
| P2 | Pin3 | GND | Ground |
| P3 | Pin1 | ANT1 | Antenna interface |
| P3 | Pin2 | ANT2 | Antenna interface |
| P4 | Pin1 | SWD | SWD debugging interface |
| P4 | Pin2 | 3.3V | Power output |
| P4 | Pin3 | SWC | SWD debugging interface |
| P4 | Pin4 | NC | Unoccupied |
| P4 | Pin5 | RST | Reset |
| P4 | Pin6 | GND | Ground |
Data formats
According to V1.0 firmware, there is one type of data output:
- Directly output a card N.O.
When a resistor (default) is soldered onto silkscreen "1" position on the board, the serial port will output a 10-digit decimal ACSII code card N.O. directly. For example: the card number is 46553491, the output data will be "0046553491", (HEX: "0x30 0x30 0x34 0x36 0x35 0x35 0x33 0x34 0x39 0x31".
Interrupt pin
- LED
According to V1.0 firmware, once an ID N.O. is read, LED pin will output a 10ms high-level pulse.
