NoticeDifference between revisions of "W5100 Ethernet Shield"
(→Hardware) |
(→Installation) |
||
| Line 93: | Line 93: | ||
==Installation== | ==Installation== | ||
| + | When install W5100 Ethernet [[shield]] to Iteaduino, please check the | ||
| + | operation voltage level of development board. If the voltage is 3.3V | ||
| + | (IFLAT32,Leafmaple), set the Operation Level Setting switch to 3.3V. | ||
| + | If the voltage is 5V(Arduino), set the Operation Level Setting switch to | ||
| + | 5V. | ||
| + | |||
| + | Iteaduino communicates with both the W5100 and SD card using the | ||
| + | SPI bus. This is on digital pins 11, 12, and 13 on the | ||
| + | UNO/Duemilanove and pins 50, 51, and 52 on the Mega. On both | ||
| + | boards, pin 10 is used to select the W5100 and pin 4 for the SD card. | ||
| + | These pins cannot be used for general I/O. On the Mega, the hardware | ||
| + | SS pin, 53, is not used to select either the W5100 or the SD card, but | ||
| + | it must be kept as an output. | ||
| + | |||
| + | Note that because the W5100 and SD card share the SPI bus, only one | ||
| + | can be active at a time. If you are using both peripherals in your | ||
| + | program, this should be taken care of by the corresponding libraries. | ||
| + | If you're not using one of the peripherals in your program, however, | ||
| + | you'll need to explicitly deselect it. To do this with the SD card, set pin | ||
| + | 4 as an output and write a high to it. For the W5100, set digital pin 10 | ||
| + | as a high output. | ||
==Indicator LED== | ==Indicator LED== | ||
Revision as of 06:50, 26 May 2014
Contents
Overview
W5100 Ethernet shield is a WIZnet W5100 breakout board with POE and Micro-SD designed for Arduino platform. 5V/3.3V compatible operation voltage level makes it compatible with Arduino boards, leafmaple, and other Arduino compatible board.
Features
- With Micro SD interface
- 5V/3.3V double operational voltage level
- 10Mb/100Mb Ethernet socket with POE
- All electronic brick interface are broken out
- Operation temperature: -40℃ ~ +85℃
Specifications
| PCB size | 55.88mm X 68.58mm X 1.6mm |
| Indicators | TX,RX,COL,FEX,SPD,LNK |
| Power supply | 5V |
| Communication Protocol | SPI |
| RoSH | Yes |
Electrical Characteristics
| Specification | Min | Type | Max | Unit |
| Power Voltage | 3V | - | 5.5 | VDC |
| Input Voltage VH: | 3 | - | 5.5 | V |
| Input Voltage VL: | -0.3 | 0 | 0.5 | V |
| Current Consumption | - | - | 100 | mA |
Hardware
| Arduino PIN | Description |
| D0 | Rx/Breakout |
| D1 | TX/Breakout |
| D2 | Breakout |
| D3 | Breakout |
| D4 | SD_CS |
| D5 | Breakout |
| D6 | Breakout |
| D7 | Breakout |
| D8 | Breakout |
| D9 | W5100_Reset |
| D10 | W5100_CS |
| D11 | MOSI |
| D12 | MISO |
| D13 | SCK |
| A0 | Breakout |
| A1 | Breakout |
| A2 | Breakout |
| A3 | Breakout |
| A4 | IIC_SDA/Breakout |
| A5 | IIC_SCL/Breakout |
Installation
When install W5100 Ethernet shield to Iteaduino, please check the operation voltage level of development board. If the voltage is 3.3V (IFLAT32,Leafmaple), set the Operation Level Setting switch to 3.3V. If the voltage is 5V(Arduino), set the Operation Level Setting switch to 5V.
Iteaduino communicates with both the W5100 and SD card using the SPI bus. This is on digital pins 11, 12, and 13 on the UNO/Duemilanove and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5100 and pin 4 for the SD card. These pins cannot be used for general I/O. On the Mega, the hardware SS pin, 53, is not used to select either the W5100 or the SD card, but it must be kept as an output.
Note that because the W5100 and SD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W5100, set digital pin 10 as a high output.
