NoticeDifference between revisions of "2.8 TFT LCD Touch Shield"
(→Software) |
|||
| Line 110: | Line 110: | ||
compatible boards. You can down load the library here: | compatible boards. You can down load the library here: | ||
[http://henningkarlsen.com/electronics/library.php?id=52 http://henningkarlsen.com/electronics/library.php?id=52] | [http://henningkarlsen.com/electronics/library.php?id=52 http://henningkarlsen.com/electronics/library.php?id=52] | ||
| + | |||
| + | ==Note== | ||
| + | Note: This shiled is 100% compatible with ITeaduino, Simplecortex. But not 100% compatible with Arduino UNO because of its big USB connecter socket. | ||
| + | |||
| + | http://imall.iteadstudio.com/media/wysiwyg/Products/ArduinoTFTShields/Arduino2.8TFTshieldERROR.jpg | ||
==Download== | ==Download== | ||
==Useful Links== | ==Useful Links== | ||
Revision as of 07:54, 23 May 2014
Contents
Overview
The Arduino 2.8”TFT Touch Shield is designed for all the Arduino compatible boards. It works in 3.3V voltage level. It can be directly plugged on the Arduino and other compatible boards. It will offer display, touch and storage functions for the Arduino board.
Features
- Arduino UNO Rev3 / Mega Shield compatible footprint
- Arduino library UTFT support
- TFTResolution : 240 x 320 pixels
- Size : 2.8"
- Colors : 262K
- Backlight : LED
- Driver IC: ILI9325DS
Specifications
| PCB size | 68.6mm X 53.3mm X 1.6mm |
| Power supply | compatible with Arduino |
| RoSH | Yes |
Electrical Characteristics
| Parameter | Min. | Typical | Max. | Unit |
| Power voltage | 4.5 | 5 | 5.5 | VDC |
| Input voltage VH | 3 | 5.5 | V | |
| Input voltage VL | -0.3 | 0 | 0.5 | V |
Hardware
Figure 1 Bottom View
Pin map of Arduino 2.8” TFT Touch Shield:
| Arduino PIN | Description |
| D0 | DB8 |
| D1 | DB9 |
| D2 | DB10 |
| D3 | DB11 |
| D4 | DB12 |
| D5 | DB13 |
| D6 | DB14 |
| D7 | DB15 |
| D8 | Touch_Dout |
| D9 | Touch_IRQ |
| D10 | SD_CS |
| D11 | SD_MOSI |
| D12 | SD_MISO |
| D13 | SD_SCK |
| A0 | Touch_Din |
| A1 | Touch_CLK |
| A2 | - |
| A3 | TFT_CS |
| A4 | TFT_WR |
| A5 | TFT_RS |
The Arduino 2.8 TFT Touch shield uses the ILI9325DS controller , it support 8bit data interface. The touch IC is TSC2046.
Operation voltage level setting switch
When using the Arduino 2.8 TFT Touch shield with 5V operation level development board – like the Arduino UNO, Arduino MEGA and so on, set the operation voltage level switch to 5V side.
When using the Arduino 2.8 TFT Touch shield with 3.3V operation level development board – like the Iteaduino BT, leaf maple, chipKit UNO and so on, set the operation voltage level switch to 3.3V side.
Software
This shield is compatible with UTFT library for Arduino, chipKit and their compatible boards. You can down load the library here: http://henningkarlsen.com/electronics/library.php?id=52
Note
Note: This shiled is 100% compatible with ITeaduino, Simplecortex. But not 100% compatible with Arduino UNO because of its big USB connecter socket.
