NoticeDifference between revisions of "2.4 TFT LCD Touch Shield V2"
m (→Useful Links) |
m (→Overview) |
||
| Line 6: | Line 6: | ||
The Arduino 2.4" TFT LCD Touch [[shield]] can work with both 3.3V and 5V, so it can dispaly on Chipkit UNO32 and Simplecortex as well. | The Arduino 2.4" TFT LCD Touch [[shield]] can work with both 3.3V and 5V, so it can dispaly on Chipkit UNO32 and Simplecortex as well. | ||
| − | '''NOTE:''' this screen adopts new chip, thus the old library is not applicable. Please use the [https://github.com/itead/ITEADLIB_Arduino_UTFT_Pro New Library]. | + | '''NOTE:''' this screen adopts new chip, thus the old library is not applicable. Please use the [https://github.com/itead/ITEADLIB_Arduino_UTFT_Pro New UTFT Library]. |
Go shopping [2.4 TFT LCD Touch shield V2(IM160418001) Coming soon!] | Go shopping [2.4 TFT LCD Touch shield V2(IM160418001) Coming soon!] | ||
Revision as of 08:32, 29 June 2016
Contents
Overview
Arduino 2.4" TFT LCD Touch shield V2 is an Arduino UNO/ Mega compatible multicolored TFT display with touch-screen and SD card socket. It is available in an Arduino shield compatible pinout for attachment. The TFT driver is based on ILI9341 with 8bit data and 4bit control interface.
The Arduino 2.4" TFT LCD Touch shield can work with both 3.3V and 5V, so it can dispaly on Chipkit UNO32 and Simplecortex as well.
NOTE: this screen adopts new chip, thus the old library is not applicable. Please use the New UTFT Library.
Go shopping [2.4 TFT LCD Touch shield V2(IM160418001) Coming soon!]
Features
- Compatible with 3.3/5V operation voltage level
- Compatible with UTFT library
- With SD Card Socket
Specifications
| PCB size | 60.2mm X 50.8mm X 1.6mm |
| Indicators | |
| Power supply | 5V |
| Communication Protocol | |
| RoSH | Yes |
Electrical Characteristics
| Parameter | Min. | Typical | Max. | Unit |
| Power voltage | 4.5 | 5 | 5.5 | VDC |
| Input voltage VH | 3 | 5.5 | V | |
| Input voltage VL | -0.3 | 0 | 0.5 | V |
Hardware
Figure 1 Bottom View
Pin map of Arduino 2.4” TFT Touch Shield:
| Arduino PIN | Description |
| D0 | DB8 |
| D1 | DB9 |
| D2 | DB10 |
| D3 | DB11 |
| D4 | DB12 |
| D5 | DB13 |
| D6 | DB14 |
| D7 | DB15 |
| D8 | Touch_Dout |
| D9 | Touch_IRQ |
| D10 | SD_CS |
| D11 | SD_MOSI |
| D12 | SD_MISO |
| D13 | SD_SCK |
| A0 | Touch_Din |
| A1 | Touch_CLK |
| A2 | - |
| A3 | TFT_CS |
| A4 | TFT_WR |
| A5 | TFT_RS |
The Arduino 2.4“E TFT Touch shield uses the ILI9341 controller,it support 8bit data interface. The touch IC is TSC2046.
Operation voltage level setting switch
When using the Arduino 2.4”E TFT Touch shield with 5V operation level development board – like the Arduino UNO, Arduino MEGA and so on, set the operation voltage level switch to 5V side.
When using the Arduino 2.4“E TFT Touch shield with 3.3V operation level development board – like the Iteaduino BT, leaf maple, chipKit UNO and so on, set the operation voltage level switch to 3.3V side.
Software
This shield is compatible with UTFT library for Arduino, chipKit and their compatible boards. You can down load the library here: http://www.rinkydinkelectronics.com/library.php?id=51
Note
Note: This shiled is 100% compatible with ITeaduino, Simplecortex. But not 100% compatible with Arduino UNO because of its big USB connecter socket.
Download
Datasheet for 2.4 TFT LCD Touch shield
Schematic for 2.4 TFT LCD Touch shield
Demo Code for 2.4 TFT LCD Touch shield
