Difference between revisions of "ITDB06"
m (→Download) |
m (→Features) |
||
Line 32: | Line 32: | ||
*802.11b mode + 20 dBm output power | *802.11b mode + 20 dBm output power | ||
*Support antenna diversity | *Support antenna diversity | ||
− | *10uA deep sleep maintain current, | + | *10uA deep sleep maintain current, less than 5 uA shutdown current |
*Built-in 32-bit lower power CUP | *Built-in 32-bit lower power CUP | ||
*SDIO 2.0, SPI, UART | *SDIO 2.0, SPI, UART |
Revision as of 03:40, 13 April 2016
Contents
Overview
The ITDB06 WiFi Wireless Module is a low-cost universal WiFi module that developed and designed by ITEAD. The module integrates industry leading Tensilica L106 ultra-low power 32-bit MCU, 16-bit compact mode, frequency supports 80MHz and 160MHz, supports RTOS, integrates Wi-Fi MAC/ BB/RF/PA/LNA, on-board antenna.
This module supports standard IEEE802.11 b/g/n protocol and complete TCP/IP protocol stack.. It allows users to add Internet of Things (IoT) to devices or to build a separate network controller.
ITDB06 is high performance wireless SOC, it provides maximum usability at the lowest cost, offering unlimited possibilities for adding WiFi functions to other systems.
ITDB06 is a complete and self-contained WiFi network solution that can run independently, it can also be mounted as a slave host MCU operation.
When the module is mounted to application and as the only processor, it can boot directly from the external flash memory. Built-in cache system is provided to increase system performance and reduce memory requirements.
When the wireless network is accessed and undertake WiFi adapter tasks, you can add it to any microcontroller-based design, simply connect SPI/SDIO interface or I2C/UART interface.
The powerful processing and storage capabilities enable it to integrate sensors and other application-specific devices through GPIO, which achieves lowest pre-development and minimal system resources occupation during performing.
This module integrates antenna switch balun and power management converter, thus little external circuitry needed, and the entire solution including the front-end module has reduced the PCB size to a new minimum.
The ITDB06 system leading features include energy saving VoIP quickly switch between sleep/ wake mode, low-power operation self-adaptive radio bias, front-end signal processing capability, troubleshooting and radio systems coexist performance eliminates interference of cellular/Bluetooth/DDR/LVDS/LCD .
Go shopping ITDB06 WiFi Wireless Module (IM151229001)
Features
- 802.11 b/g/n
- WIFI @2.4 GHz,support WPA/WPA2 safe mode
- Small size 11.5mm*11.5mm
- Built-in 10 bit high accuracy ADC
- Built-in TCP/IP protocol stack
- Built-in switch, balun, LNA, power amplifier and matching network
- Built-in PLL, voltage stabilizer and power management components
- 802.11b mode + 20 dBm output power
- Support antenna diversity
- 10uA deep sleep maintain current, less than 5 uA shutdown current
- Built-in 32-bit lower power CUP
- SDIO 2.0, SPI, UART
- STBC, 1x1 MIMO, 2x1 MIMO
- A-MPDU&A-MSDU aggregation and 0.4us guard interval
- Wake-up, connect and transfer data packets in 2 ms
- Standby power consumption: <1.0mW (DTIM3)
- Temp range:-40 ~ 125℃
Specification
Category | Parameters | Explanation |
---|---|---|
Radio parameters | Wireless Standard | 802.11 b/g/n |
Frequency Range | 2.4G-25G(2400M-2483.5M) | |
Transmitting power | 802.11b: 20dBm | |
802.11g: 17dBm | ||
802.11n: 14dBm | ||
Receiving sensitivity | 802.11b: (11Mbps)-91dbm | |
802.11g: (54Mbps)-75dbm | ||
802.11n: (MCS7)-72dbm | ||
Hardware parameters | Data access | UART/HSPI/I2C/I2S/Ir Remote Control |
GPIO/PWM | ||
Operating Voltage | 3.0~3.6V(Suggested 3.3V) | |
Working current | Average: 80mA | |
Operating temperature | -40℃~125℃ | |
Storage temperature | Room temperature | |
Size | 16mm*24mm*3mm | |
Software parameters | Wireless Network Mode | Station/softAP/SoftAP+station |
Security Mechanism | WPA/WPA2 | |
Encryption Type | WEP/TKIP/AES | |
Upgrading firmware | Local serial programming / Cloud Upgrade / Host Download Burn | |
Network protocol | IPv4, TCP/UDP/HTTP/FTP | |
User Profiles | AT + instruction set, cloud server, Android/iOS APP |
Electrical Characteristics
Parameter | Condition | Min | Type | Max | Unit |
---|---|---|---|---|---|
Storage temperature | -40 | Room temp. | 125 | ℃ | |
Max solder temperature | IPC/JEDEC J-STD-020 | 260 | ℃ | ||
Working voltage | 3.0 | 3.3 | 3.6 | V | |
I/O VIL/VIH | -0.3/0.75VIO | 0.25VIO/3.6 | V | ||
I/O VPL/VOH | N/0.8VIO | 0.1VIO/N | V | ||
I/O Imax | 12 | mA |
Hardware
PIN MAP
No | Pin_Name | Function_Description |
---|---|---|
1 | RST | Reset Module |
2 | ADC | A / D conversion result. Input voltage range: 0~1V, value range: 0~1024 |
3 | EN | Chip enable end, high active |
4 | IO16 | GPIO16; wakeup from deep sleep when connect RESET pin。 |
5 | IO14 | GPIO14; HSPI_CLK |
6 | IO12 | GPIO12; HSPI_MISO |
7 | IO13 | GPIO13; HSPI_MOSI; UART0_CTS |
8 | VCC | 3.3V |
9 | CS0 | Chip Select |
10 | MISO | Master Input Slave Output |
11 | IO9 | GPIO9 |
12 | IO10 | GPIO10 |
13 | MOSI | Master Output Slave Input |
14 | SCLK | Clock (SCL) |
15 | GND | GND |
16 | IO15 | GPIO15; MTDO; HSPICS; UART0_RTS |
17 | IO2 | GPIO2; UART1_TXD |
18 | IO0 | GPIO0 |
19 | IO4 | GPIO4 |
20 | IO5 | GPIO5 |
21 | RXD | UART0_RXD; GPIO3 |
22 | TXD | UART0_TXD; GPIO1 |
Mode | GPIO15 | GPIO0 | GPIO2 |
---|---|---|---|
UART Download mode | Low | Low | High |
Flash Boot Mode | Low | High | High |
Instruction
Download
File:IM151229001 ITDB06 VIEW.pdf
File:IM151229001 ITDB06 SCH.pdf
File:IM151229001 ITDB06 dimension.pdf
- ITDB06 Module added some features on the basics of ESP8266 module. You can refer to below documents to use ITDB06:
File:4A-ESP8266__AT Instruction Set__EN_v0.24.pdf
File:ITDB06-AT_Instruction_Set.pdf