NoticeDifference between revisions of "Foca Pro"
m (→Hardware) |
m (→Overview) |
||
| Line 2: | Line 2: | ||
[[File:IM141125006_4.jpg|400px|thumb|right]] | [[File:IM141125006_4.jpg|400px|thumb|right]] | ||
[[Foca]] Pro is a USB to serial UART board with XBee interface socket. It’s the essential tools for establishing communication between PC and mostly MCU or use XBee. Especially, it’s a optimum [[tool]] for some Arduino based boards without USB interface, like Sniffer Nano, [[Colorduino]] and etc. | [[Foca]] Pro is a USB to serial UART board with XBee interface socket. It’s the essential tools for establishing communication between PC and mostly MCU or use XBee. Especially, it’s a optimum [[tool]] for some Arduino based boards without USB interface, like Sniffer Nano, [[Colorduino]] and etc. | ||
| + | |||
| + | Go shopping [http://imall.iteadstudio.com/im141125006.html Foca Pro(IM141125006)] | ||
==Specification== | ==Specification== | ||
Latest revision as of 07:44, 14 January 2015
Contents
Overview
Foca Pro is a USB to serial UART board with XBee interface socket. It’s the essential tools for establishing communication between PC and mostly MCU or use XBee. Especially, it’s a optimum tool for some Arduino based boards without USB interface, like Sniffer Nano, Colorduino and etc.
Go shopping Foca Pro(IM141125006)
Specification
| PCB size | 26mm X 49.6mm X 1.6mm |
| Voltage Input | 5V |
| Interface | UART |
| Indicator | PWR |
Features
- Single chip USB to asynchronous serial data transfer interface
- Entire USB protocol handled on the chip – No firmware programming require
- 5V Single Supply Operation and compatible with 3.3V/5V operation voltage
- USB 2.0 Full Speed compatible
- Compatible with Xbee
- Compatible with 2.00mm Grove Electronic Interface
Electronic Characteristics
| Min | Typical | Max | Unit | |
| Power Supply | 4.5 | 5 | 5.5 | VDC |
| Input voltage VinH(Target Voltage = 3.3V ) | 3 | 3.3 | 3.6 | V |
| Input voltage VinH(Target Voltage = 5V ) | 4.5 | 5 | 5.5 | V |
| Input voltage VinL | -0.3 | 0 | 0.5 | V |
| Current Consumption | - | 20 | 40 | mA |
Hardware
Pin Map
| Pin | Pin name | Description |
| 1 | DTR | Data Terminal Ready Control Output |
| 2 | GND | Ground |
| 3 | RXD | Receiving Data Input |
| 4 | TXD | Transmit Data Output |
| 5 | VIO | 5V/3.3V |
Driver Installation
Foca Pro adopts CP2102 chip instead of FT232RL chip on Foca board, thus we cannot use driver file in the driver directory of Arduino IDE to install the driver. http://www.silabs.com/products/interface/usbtouart/Pages/usb-to-uart-bridge.aspx
You can download CP2102 driver for different platforms including MAC version, Linux version and Windows version. Once downloaded, plug in Foca Pro, search for CP2102 among the unknown devices, then click Upgrade Driver and manually install. Point the driver position to the downloaded driver directory and then install, finally the corresponding serial number can be found on IDE.
More details of installation instructions, you can refer to this file: ftp://imall.iteadstudio.com/Mainboard/IM130615004_ITeaduino_Nano/DOC_Driver_Installation.pdf
