NoticeDifference between revisions of "Iteaduino DUE"
(→Hardware) |
(→Spec) |
||
| Line 29: | Line 29: | ||
http://imall.iteadstudio.com/media/wysiwyg/Products/Mainboard/IM130413001_1.jpg | http://imall.iteadstudio.com/media/wysiwyg/Products/Mainboard/IM130413001_1.jpg | ||
| − | ==Spec== | + | ==Spec== |
| − | + | {| border="1" | |
| − | + | ||
| − | + | |- | |
| − | + | | Microcontroller | |
| − | + | | AT91SAM3X8E | |
| − | + | ||
| − | + | |- | |
| − | + | | Operating Voltage | |
| − | + | | 3.3V | |
| − | + | |- | |
| − | + | | POWER Supply Voltage(recommanded) | |
| − | + | | 7~24V | |
| − | + | |- | |
| + | | Power supply Max Voltage | ||
| + | | 26V | ||
| + | |- | ||
| + | | Digital IO pins | ||
| + | | 54(of which 12 provide PWM output) | ||
| + | |- | ||
| + | | Analog Input pins(ADC) | ||
| + | | 12 | ||
| + | |- | ||
| + | | Analog Output pins(DAC) | ||
| + | | 2 | ||
| + | |- | ||
| + | | Total DC Output current on all IO lines | ||
| + | | 130mA | ||
| + | |- | ||
| + | | DC current of 3.3V | ||
| + | | 800mA | ||
| + | |- | ||
| + | | DC current of 5V | ||
| + | | 800mA | ||
| + | |- | ||
| + | | Flash Memory | ||
| + | | 512KB all available for user application | ||
| + | |- | ||
| + | | SRAM | ||
| + | | 96KB(2 banks:64KB and 32KB) | ||
| + | |- | ||
| + | | Clock frequency | ||
| + | | 84MHz | ||
| + | |} | ||
==Download== | ==Download== | ||
Revision as of 06:57, 19 May 2014
Contents
Overview
Iteaduino DUE is a microcontroller board based on the Atmel SAM3X8E ARM Crotex-M3 core. It is the improvement board based on the Arduino DUE. It has 54 digital IO pins, 12 analog inputs, 4 UARTs, a 84MHz clock, an USB OTG capable connection, 2 DACs, 2 IIC, a power jack, an SPI header, a reset button and an erase button.
Warning: Unlike other Iteadduino boards, the Iteaduino Due board runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Providing higher voltages, like 5V to an I/O pin could damage the board.
The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with a AC-to-DC adapter or battery to get started. The Due is compatible with all Arduino compatible shields that work at 3.3V and are compliant with the 1.0 Arduino compatible pinout.
The Due follows the 1.0 pinout:
TWI: SDA and SCL pins that are near to the AREF pin.
The IOREF pin which allows an attached shield with the proper configuration to adapt to the voltage provided by the board. This enables shield compatibility with a 3.3V board like the Due and AVR-based boards which operate at 5V. An unconnected pin, reserved for future use.
ARM Core benefits
The Due has a 32-bit ARM core that can outperform typical 8-bit microcontroller boards. The most significant differences are:
A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock.
CPU Clock at 84Mhz.
96 KBytes of SRAM.
512 KBytes of Flash memory for code.
A DMA controller, that can relieve the CPU from doing memory intensive tasks.
Hardware
Spec
| Microcontroller | AT91SAM3X8E |
| Operating Voltage | 3.3V |
| POWER Supply Voltage(recommanded) | 7~24V |
| Power supply Max Voltage | 26V |
| Digital IO pins | 54(of which 12 provide PWM output) |
| Analog Input pins(ADC) | 12 |
| Analog Output pins(DAC) | 2 |
| Total DC Output current on all IO lines | 130mA |
| DC current of 3.3V | 800mA |
| DC current of 5V | 800mA |
| Flash Memory | 512KB all available for user application |
| SRAM | 96KB(2 banks:64KB and 32KB) |
| Clock frequency | 84MHz |
