Difference between revisions of "Translations:IR Shield/7/en"

From ITEAD Wiki
Jump to: navigation, search
(Importing a new version from external source)
 
m
 
Line 1: Line 1:
−
==Pin Map==
+
==引脚图==
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
−
| align="center" style="background:#f0f0f0;"|'''Arduino Pin'''
+
| align="center" style="background:#f0f0f0;"|'''Arduino引脚'''
−
| align="center" style="background:#f0f0f0;"|'''Description'''
+
| align="center" style="background:#f0f0f0;"|'''描述'''
 
|-
 
|-
 
| D0||XBEE_TX
 
| D0||XBEE_TX
Line 46: Line 46:
 
|-
 
|-
 
|}
 
|}
−
*IR_TX: when D3 is set as high level switch, IR Diode will emit signals out. When D3 is set as low level switch, IR Diode won’t work.
+
*IR_TX: 当D3设置为高电平，红外发射管会向外发射信号；当D3设置为低电平，红外发射管不工作。
−
*IR_RX: Use HS0038B as IR receiving module
+
 
−
*Jumpers:
+
*IR_RX: 使用HS0038B作为IR接收模块。
−
:Jumpers can directly connect to Arduino’s IO. If you don’t need them or their corresponding pins are occupied, you can remove the jumpers.
+
 
−
:*A0: insert a 10K resistance to A0 button
+
*Jumpers：跳线帽是直接连接到Arduino的IO 上，如果不需要或引脚被其他模块占用时，请移除其跳线帽。
−
:*LED1: connect to D6 pin. If the output voltage is high, LED1 turns on.
+
 
−
:*LED2: connect to D7 pin. If the output voltage is high, LED1 turns on.
+
:A0：上拉一个10K电阻到A0按钮上。
−
*Switch: Set the switch level according to Arduino main board. When the mainboard is set in 5V, you should turn the switch to 5V; when in 3.3V, you should turn to 3.3V.
+
 
 +
:LED1：连接到D6引脚，置高时LED1会亮。
 +
 
 +
:LED2：连接到D7引脚，置高时LED2会亮。
 +
 
 +
*Switch：根据Arduino主板的操作电平来设置，当主板工作在5V，开关打到5V；当主板工作在3.3V，开关打到3V3。

Latest revision as of 02:05, 9 August 2014

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (IR Shield)
==Pin Map==
{| class="wikitable"
|-
| align="center" style="background:#f0f0f0;"|'''Arduino Pin'''
| align="center" style="background:#f0f0f0;"|'''Description'''
|-
| D0||XBEE_TX
|-
| D1||XBEE_RX
|-
| D2||nRF24L01_IRQ & STD Button
|-
| D3||IR_TX*
|-
| D4||SD_CS
|-
| D5||IR_RX*
|-
| D6||LED1*
|-
| D7||LED2*
|-
| D8||-
|-
| D9||nRF24L01_CE
|-
| D10||nRF24L01_CS
|-
| D11||MOSI
|-
| D12||MISO
|-
| D13||SCK
|-
| A0||A0 Button
|-
| A1||-
|-
| A2||-
|-
| A3||-
|-
| A4||SHT10_SDA
|-
| A5||SHT10_SCL
|-
|}
*IR_TX: when D3 is set as high level switch, IR Diode will emit signals out. When D3 is set as low level switch, IR Diode won’t work.
*IR_RX: Use HS0038B as IR receiving module
*Jumpers:
:Jumpers can directly connect to Arduino’s IO. If you don’t need them or their corresponding pins are occupied, you can remove the jumpers.
:*A0: insert a 10K resistance to A0 button
:*LED1: connect to D6 pin. If the output voltage is high, LED1 turns on.
:*LED2: connect to D7 pin. If the output voltage is high, LED1 turns on.
*Switch: Set the switch level according to Arduino main board. When the mainboard is set in 5V, you should turn the switch to 5V; when in 3.3V, you should turn to 3.3V.
Translation==引脚图==
{| class="wikitable"
|-
| align="center" style="background:#f0f0f0;"|'''Arduino引脚'''
| align="center" style="background:#f0f0f0;"|'''描述'''
|-
| D0||XBEE_TX
|-
| D1||XBEE_RX
|-
| D2||nRF24L01_IRQ & STD Button
|-
| D3||IR_TX*
|-
| D4||SD_CS
|-
| D5||IR_RX*
|-
| D6||LED1*
|-
| D7||LED2*
|-
| D8||-
|-
| D9||nRF24L01_CE
|-
| D10||nRF24L01_CS
|-
| D11||MOSI
|-
| D12||MISO
|-
| D13||SCK
|-
| A0||A0 Button
|-
| A1||-
|-
| A2||-
|-
| A3||-
|-
| A4||SHT10_SDA
|-
| A5||SHT10_SCL
|-
|}
*IR_TX: 当D3设置为高电平，红外发射管会向外发射信号；当D3设置为低电平，红外发射管不工作。

*IR_RX: 使用HS0038B作为IR接收模块。

*Jumpers：跳线帽是直接连接到Arduino的IO 上，如果不需要或引脚被其他模块占用时，请移除其跳线帽。

:A0：上拉一个10K电阻到A0按钮上。

:LED1：连接到D6引脚，置高时LED1会亮。

:LED2：连接到D7引脚，置高时LED2会亮。

*Switch：根据Arduino主板的操作电平来设置，当主板工作在5V，开关打到5V；当主板工作在3.3V，开关打到3V3。

引脚图

Arduino引脚 描述
D0 XBEE_TX
D1 XBEE_RX
D2 nRF24L01_IRQ & STD Button
D3 IR_TX*
D4 SD_CS
D5 IR_RX*
D6 LED1*
D7 LED2*
D8 -
D9 nRF24L01_CE
D10 nRF24L01_CS
D11 MOSI
D12 MISO
D13 SCK
A0 A0 Button
A1 -
A2 -
A3 -
A4 SHT10_SDA
A5 SHT10_SCL
  • IR_TX: 当D3设置为高电平，红外发射管会向外发射信号；当D3设置为低电平，红外发射管不工作。
  • IR_RX: 使用HS0038B作为IR接收模块。
  • Jumpers：跳线帽是直接连接到Arduino的IO 上，如果不需要或引脚被其他模块占用时，请移除其跳线帽。
A0：上拉一个10K电阻到A0按钮上。
LED1：连接到D6引脚，置高时LED1会亮。
LED2：连接到D7引脚，置高时LED2会亮。
  • Switch：根据Arduino主板的操作电平来设置，当主板工作在5V，开关打到5V；当主板工作在3.3V，开关打到3V3。
Retrieved from "https://wiki.iteadstudio.com/index.php?title=Translations:IR_Shield/7/en&oldid=2412"