NoticeDifference between revisions of "Sonoff SV"
m (→Overview) |
m (→Useful Links) |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 45: | Line 45: | ||
• Standby power consumption is less than 1.0 mW (DTIM3) | • Standby power consumption is less than 1.0 mW (DTIM3) | ||
| − | + | • Other parameters are as follows | |
| − | + | ||
| − | • Other parameters as follows | + | |
{| class="wikitable" | {| class="wikitable" | ||
| Line 59: | Line 57: | ||
|Frequency range||2.4GHz-2.5GHz (2400M-2483.5M) | |Frequency range||2.4GHz-2.5GHz (2400M-2483.5M) | ||
|- | |- | ||
| − | |rowspan= | + | |rowspan=6 | Hardware Parameter|| rowspan=2 |Data port||UART/I2C |
|- | |- | ||
|GPIO/PWM | |GPIO/PWM | ||
| Line 67: | Line 65: | ||
|Operating current||Average： 80mA | |Operating current||Average： 80mA | ||
|- | |- | ||
| − | |Operating temperature||- | + | |Operating temperature||0ºC-40ºC(32°F-104°F) |
| − | + | ||
| − | + | ||
|- | |- | ||
|Package size ||65mm*34mm*16mm | |Package size ||65mm*34mm*16mm | ||
| Line 152: | Line 148: | ||
[http://ewelink.coolkit.cc/?p=151 User Manual for Sonoff SV] | [http://ewelink.coolkit.cc/?p=151 User Manual for Sonoff SV] | ||
| + | |||
| + | [https://www.itead.cc/wiki/EWeLink_Introduction eWeLink Step-By-Step Guide] | ||
Latest revision as of 08:22, 28 July 2017
Contents
Overview
.JPG)
Sonoff SV(safe voltage) is a low power supply Sonoff version,which supports 5-24V power supply. The power separation circuit enables it to control AC or DC power for the connected device, but you need to do some welding to realize this function, please refer to Solder Instructions below. Sonoff SV has GIPO reserved to support secondary development. This version does not have 433MHz RF function.
Go shopping Sonoff SV (SKU:IM160220004)
Features
- Support 5~24V power supply.
- Support fast configure SSID and password through APP.
- Support automatic connect to server, register and update status info.
- Support tracking device status and timely remote control through APP.
- Support setting single/repeat/countdown timing tasks.
- Reserve GIPO for secondary development.
WIFI Characteristics
• 802.11 b / g / n
• Built-in Tensilica L106 ultra-low power consumption 32-bit micro-MCU, dominant frequency support 80 MHz and 160 MHz, support RTOS
• Built-in TCP / IP protocol stack
• Built-in TR switch, balun, LNA, power amplifier and matching network
• Built-in PLL, voltage regulator and power supply management components, 802.11b mode +20 dBm output power
• A-MPDU&A-MSDU aggregation and 0.4μs guard interval
• WiFi @ 2.4 GHz, supports WPA / WPA2 safe mode
• Support cloud OTA upgrade
• Support STA / AP / STA + AP mode
• UART, I2C, PWM, GPIO
• Deep sleep maintain current is 10 uA, shutdown current is less than 5 uA
• Wake-up, connect and transfer data packets in 2 ms
• Standby power consumption is less than 1.0 mW (DTIM3)
• Other parameters are as follows
| Category | Parameters | Description |
| Wireless Parameter | Wireless standard | 802.11 b/g/n |
| Frequency range | 2.4GHz-2.5GHz (2400M-2483.5M) | |
| Hardware Parameter | Data port | UART/I2C |
| GPIO/PWM | ||
| Operating voltage | 3.0~3.6V(recommend 3.3V) | |
| Operating current | Average： 80mA | |
| Operating temperature | 0ºC-40ºC(32°F-104°F) | |
| Package size | 65mm*34mm*16mm | |
| Software Parameter | Wireless network mode | station/softAP/SoftAP+station |
| Security mechanism | WPA/WPA2 | |
| Encryption type | WEP/TKIP/AES | |
| Firmware upgration | Local serial programming/Cloud Upgrade/Host download programming | |
| Software development | Support secondary development | |
| Network protocols | IPv4, TCP/UDP/HTTP/FTP | |
| User configuration | cloud server, Android/iOS APP |
Specification
| PCB Size | 65X34X1.2mm |
| Interface | UART |
| Indicator LED | WiFi，on/off |
Electrical Characteristics
| Characteristics | Symbol | Min | Typ | Max | Unit |
| Power supply voltage | VDD | 5 | - | 24 | V |
| Operation current for VDD | IDD | - | - | 290 | mA |
Hardware
Solder Instructions
Pin Map
| Pin Index | Pin Name | Description |
| 1 | 3V3 | Chip power |
| 2 | TX | Serial transmit port |
| 3 | RX | Serial receiving port |
| 4 | GND | GND |
| 5 | GPIO4 | I/O |
| 6 | GPIO5 | I/O |
| 7 | GPIO14 | I/O |
