NoticeDifference between revisions of "Arduino 3.2 TFT LCD Touch Shield V2"
m (→Overview) |
m (→Features) |
||
| Line 12: | Line 12: | ||
==Features== | ==Features== | ||
* Arduino Mega [[Shield]] compatible footprint | * Arduino Mega [[Shield]] compatible footprint | ||
| − | * Arduino | + | * Arduino new UTFT library support |
* TFTResolution : 240 x 320 pixels | * TFTResolution : 240 x 320 pixels | ||
* Size : 3.2" | * Size : 3.2" | ||
Revision as of 08:37, 29 June 2016
Contents
Overview
Arduino 3.2" TFT LCD Touch shield V2 is an Arduino Mega compatible multicolored TFT display with touch-screen and SD card socket. It is available in an Arduino MEGA shield compatible pinout for attachment. The TFT driver is based on ILI9341 with 8bit data and 4bit control interface.
The Arduino 3.2" TFT LCD Touch shield V2 can work with both 3.3V and 5V, so it can dispaly on Chipkit MAX32 as well.
NOTE: this screen adopts new chip, thus the old library is not applicable. Please use the New UTFT Library.
Go shopping [3.2 TFT LCD Touch Shield V2(IM160418006) Coming Soon!!!]
Features
- Arduino Mega Shield compatible footprint
- Arduino new UTFT library support
- TFTResolution : 240 x 320 pixels
- Size : 3.2"
- Colors : 65K
- Backlight : LED
- Driver IC: ILI9341
Specifications
| PCB size | 79.3mm X 57.5mm X 1.6mm |
| Indicators | - |
| Power supply | compatible with Arduino Mega |
| Communication Protocol | - |
| RoHS | Yes |
Electrical Characteristics
| Specification | Min | Type | Max | Unit |
| Power Voltage | 4.5 | 5 | 5.5 | VDC |
| Input Voltage VH: | 3 | - | 5.5 | V |
| Input Voltage VL: | -0.3 | 0 | 0.5 | V |
Hardware
Figure 1 Bottom View
Pin map of Arduino 3.2” TFT Touch Shield V2:
| Arduino Mega PIN | Description |
| D2 | T_IRQ |
| D3 | T_DOUT |
| D4 | T_DIN |
| D5 | T_CS |
| D6 | T_CLK |
| D22 | DB8 |
| D23 | DB9 |
| D24 | DB10 |
| D25 | DB11 |
| D26 | DB12 |
| D27 | DB13 |
| D28 | DB14 |
| D29 | DB15 |
| D30 | DB7 |
| D31 | DB6 |
| D32 | DB5 |
| D33 | DB4 |
| D34 | DB3 |
| D35 | DB2 |
| D36 | DB1 |
| D37 | DB0 |
| D38 | RS |
| D39 | WR |
| D40 | CS |
| D41 | RST |
| D50 | SD_MISO |
| D51 | SD_MOSI |
| D52 | SD_SCK |
| D53 | SD_NSS |
The Arduino 3.2” Touch shield V2 uses the ILI9341 controller , it support 16bit data interface. The touch IC is XPT2046.
Operation voltage level setting switch
When using the Arduino 3.2 TFT Touch shield V2 with 5V operation level development board – like Arduino MEGA and so on, set the operation voltage level switch to 5V side.
When using the Arduino 3.2 TFT Touch shield V2 with 3.3V operation level development board set the operation voltage level switch to 3.3V side.
Software
This shield is compatible with UTFT library for Arduino Mega, chipKitMax32 and their compatible boards. You can down load the library here: http://www.rinkydinkelectronics.com/library.php?id=51
Download
Datasheet for 3.2 TFT LCD Touch Shield
