Difference between revisions of "ITDB06"

From ITEAD Wiki
Jump to: navigation, search
m (Download)
m (Useful link)
Line 188: Line 188:
  
 
==Useful link==
 
==Useful link==
 +
Firmware Update Tutorial: https://www.itead.cc/blog/esp8266-firmware-update-general-tutorial

Revision as of 03:44, 8 June 2016

Overview

IM151229001 ITDB06.JPG

The ITDB06 WiFi Wireless Module is a low-cost universal WiFi module that developed and designed by ITEAD. The module integrates industry leading Tensilica L106 ultra-low power 32-bit MCU, 16-bit compact mode, frequency supports 80MHz and 160MHz, supports RTOS, integrates Wi-Fi MAC/ BB/RF/PA/LNA, on-board antenna.

This module supports standard IEEE802.11 b/g/n protocol and complete TCP/IP protocol stack.. It allows users to add Internet of Things (IoT) to devices or to build a separate network controller.

ITDB06 is high performance wireless SOC, it provides maximum usability at the lowest cost, offering unlimited possibilities for adding WiFi functions to other systems.

ITDB06 Blocks.jpg

ITDB06 is a complete and self-contained WiFi network solution that can run independently, it can also be mounted as a slave host MCU operation.

When the module is mounted to application and as the only processor, it can boot directly from the external flash memory. Built-in cache system is provided to increase system performance and reduce memory requirements.

When the wireless network is accessed and undertake WiFi adapter tasks, you can add it to any microcontroller-based design, simply connect SPI/SDIO interface or I2C/UART interface.

The powerful processing and storage capabilities enable it to integrate sensors and other application-specific devices through GPIO, which achieves lowest pre-development and minimal system resources occupation during performing.

This module integrates antenna switch balun and power management converter, thus little external circuitry needed, and the entire solution including the front-end module has reduced the PCB size to a new minimum.

The ITDB06 system leading features include energy saving VoIP quickly switch between sleep/ wake mode, low-power operation self-adaptive radio bias, front-end signal processing capability, troubleshooting and radio systems coexist performance eliminates interference of cellular/Bluetooth/DDR/LVDS/LCD .

Go shopping ITDB06 WiFi Wireless Module (IM151229001)

Features

  • 802.11 b/g/n
  • WIFI @2.4 GHz,support WPA/WPA2 safe mode
  • Small size 11.5mm*11.5mm
  • Built-in 10 bit high accuracy ADC
  • Built-in TCP/IP protocol stack
  • Built-in switch, balun, LNA, power amplifier and matching network
  • Built-in PLL, voltage stabilizer and power management components
  • 802.11b mode + 20 dBm output power
  • Support antenna diversity
  • 10uA deep sleep maintain current, less than 5 uA shutdown current
  • Built-in 32-bit lower power CUP
  • SDIO 2.0, SPI, UART
  • STBC, 1x1 MIMO, 2x1 MIMO
  • A-MPDU&A-MSDU aggregation and 0.4us guard interval
  • Wake-up, connect and transfer data packets in 2 ms
  • Standby power consumption: <1.0mW (DTIM3)
  • Temp range:-40 ~ 125℃

Specification

Category Parameters Explanation
Radio parameters Wireless Standard 802.11 b/g/n
Frequency Range 2.4G-25G(2400M-2483.5M)
Transmitting power 802.11b: 20dBm
802.11g: 17dBm
802.11n: 14dBm
Receiving sensitivity 802.11b: (11Mbps)-91dbm
802.11g: (54Mbps)-75dbm
802.11n: (MCS7)-72dbm
Hardware parameters Data access UART/HSPI/I2C/I2S/Ir Remote Control
GPIO/PWM
Operating Voltage 3.0~3.6V(Suggested 3.3V)
Operating current Average: 80mA
Operating temperature -40℃~125℃
Storage temperature Room temperature
Size 16mm*24mm*3mm
Software parameters Wireless Network Mode Station/softAP/SoftAP+station
Security Mechanism WPA/WPA2
Encryption Type WEP/TKIP/AES
Upgrading firmware Local serial programming / Cloud Upgrade / Host Download Burn
Network protocol IPv4, TCP/UDP/HTTP/FTP
User Profiles AT + instruction set, cloud server, Android/iOS APP

Electrical Characteristics

Parameter Condition Min Type Max Unit
Storage temperature -40 Room temp. 125
Max solder temperature IPC/JEDEC J-STD-020 260
Operating voltage 3.0 3.3 3.6 V
I/O VIL/VIH -0.3/0.75VIO 0.25VIO/3.6 V
I/O VPL/VOH N/0.8VIO 0.1VIO/N V
I/O Imax 12 mA

Hardware

IM151229001 ITDB06 Hardware.png

PIN MAP

IM151229001 ITDB06 pin map.png

No Pin_Name Function_Description
1 RST Reset Module
2 ADC A / D conversion result. Input voltage range: 0~1V, value range: 0~1024
3 EN Chip enable end, high active
4 IO16 GPIO16; wakeup from deep sleep when connect RESET pin。
5 IO14 GPIO14; HSPI_CLK
6 IO12 GPIO12; HSPI_MISO
7 IO13 GPIO13; HSPI_MOSI; UART0_CTS
8 VCC 3.3V
9 CS0 Chip Select
10 MISO Master Input Slave Output
11 IO9 GPIO9
12 IO10 GPIO10
13 MOSI Master Output Slave Input
14 SCLK Clock (SCL)
15 GND GND
16 IO15 GPIO15; MTDO; HSPICS; UART0_RTS
17 IO2 GPIO2; UART1_TXD
18 IO0 GPIO0
19 IO4 GPIO4
20 IO5 GPIO5
21 RXD UART0_RXD; GPIO3
22 TXD UART0_TXD; GPIO1
Mode GPIO15 GPIO0 GPIO2
UART Download mode Low Low High
Flash Boot Mode Low High High

Instruction

IM151229001 ITDB06 connection.png

Download

File:IM151229001 ITDB06 VIEW.pdf

File:IM151229001 ITDB06 SCH.pdf

File:IM151229001 ITDB06 dimension.pdf

  • ITDB06 Module added some features on the basics of ESP8266 module. You can refer to below documents to use ITDB06:

File:4A-ESP8266__AT Instruction Set__EN_v0.24.pdf

File:ITDB06-AT_Instruction_Set.pdf

ITDB06-W25Q80-1.0.0

Useful link

Firmware Update Tutorial: https://www.itead.cc/blog/esp8266-firmware-update-general-tutorial