NoticeDifference between revisions of "RBoard"
(→Pin Map List) |
(→PWR_EXT Setting) |
||
| Line 94: | Line 94: | ||
==PWR_EXT Setting== | ==PWR_EXT Setting== | ||
| + | Rboard is designed for isolating industrial application with external power supply. So when | ||
| + | remove the jumpers on PWR_EXT, use the DC 7-20 terminal to for ATMega328 and all digital | ||
| + | circuit power supply, and supply the 5V relay by the PWR_EXT terminal with 5V, there are 2 | ||
| + | completely isolated power systems for controller part and relay part. | ||
| + | |||
| + | If you don't need so stringent electrical isolation, put the jumpers on PWR_EXT, then you don't | ||
| + | need an extra power supply, the relays will supply by the DC 7-20 terminal the same as controller | ||
| + | part - but there also the opto-isolation between the relay and controller I/Os. | ||
==Download== | ==Download== | ||
Revision as of 09:06, 20 May 2014
Contents
Overview
Rboard is a unique Arduino board which features 4 channels isolated relays, an XBee socket, and an ATMega328. This board will add relay control as well as wireless connectivity to your projects. It’s great for anything from home automation to robot control. The possibilities are endless!
Spec
| PCB size | 78.74mm X 106.08mm X 1.6mm |
| Power supply | 6~20V DC |
| Microprocessor | Atmega328 |
| Indicators | PWR, PWR_EXT, C0, C1, C2, C3 |
| Communication Interface | XBee, nRF24L01+, UART |
| RoSH | Yes |
Electrical Characteristics
| Specification | Min. | Typical Value | Max. | Unit |
|---|---|---|---|---|
| Power Voltage | 6 | - | 20 | VDC |
| Input Voltage VH (Target Voltage = 3.3V) | 3 | 3.3 | 3.6 | V |
| Input Voltage VL: | -0.3 | 0 | 0.5 | V |
| Current Consumption | - | 100 | 500 | mA |
Hardware
Top View Map
Pin Map List
| Pin of Arduino | Description |
| D0 | RxD |
| D1 | TxD |
| D2 | Xbee Reset |
| D3 | nRF24L01+_IRQ |
| D4 | R0 |
| D5 | R1 |
| D6 | R2 |
| D7 | R3 |
| D8 | nRF24L01+_CE |
| D9 | nRF24L01+_CS |
| D10 | SD_CS |
| D11 | SPI_MOSI |
| D12 | SPI_MISO |
| D13 | SPI_SCK |
| A0 | AD0 |
| A1 | AD1 |
| A2 | AD2 |
| A3 | AD3 |
| A4 | AD4/IIC_SCL |
| A5 | AD5/IIC_SDA |
PWR_EXT Setting
Rboard is designed for isolating industrial application with external power supply. So when remove the jumpers on PWR_EXT, use the DC 7-20 terminal to for ATMega328 and all digital circuit power supply, and supply the 5V relay by the PWR_EXT terminal with 5V, there are 2 completely isolated power systems for controller part and relay part.
If you don't need so stringent electrical isolation, put the jumpers on PWR_EXT, then you don't need an extra power supply, the relays will supply by the DC 7-20 terminal the same as controller part - but there also the opto-isolation between the relay and controller I/Os.
