Difference between revisions of "Translations:IR Shield/7/en"

From ITEAD Wiki
Jump to: navigation, search
(Importing a new version from external source)
(No difference)

Revision as of 02:00, 9 August 2014

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (IR Shield)
==Pin Map==
{| class="wikitable"
|-
| align="center" style="background:#f0f0f0;"|'''Arduino Pin'''
| align="center" style="background:#f0f0f0;"|'''Description'''
|-
| D0||XBEE_TX
|-
| D1||XBEE_RX
|-
| D2||nRF24L01_IRQ & STD Button
|-
| D3||IR_TX*
|-
| D4||SD_CS
|-
| D5||IR_RX*
|-
| D6||LED1*
|-
| D7||LED2*
|-
| D8||-
|-
| D9||nRF24L01_CE
|-
| D10||nRF24L01_CS
|-
| D11||MOSI
|-
| D12||MISO
|-
| D13||SCK
|-
| A0||A0 Button
|-
| A1||-
|-
| A2||-
|-
| A3||-
|-
| A4||SHT10_SDA
|-
| A5||SHT10_SCL
|-
|}
*IR_TX: when D3 is set as high level switch, IR Diode will emit signals out. When D3 is set as low level switch, IR Diode won’t work.
*IR_RX: Use HS0038B as IR receiving module
*Jumpers:
:Jumpers can directly connect to Arduino’s IO. If you don’t need them or their corresponding pins are occupied, you can remove the jumpers.
:*A0: insert a 10K resistance to A0 button
:*LED1: connect to D6 pin. If the output voltage is high, LED1 turns on.
:*LED2: connect to D7 pin. If the output voltage is high, LED1 turns on.
*Switch: Set the switch level according to Arduino main board. When the mainboard is set in 5V, you should turn the switch to 5V; when in 3.3V, you should turn to 3.3V.
Translation==Pin Map==
{| class="wikitable"
|-
| align="center" style="background:#f0f0f0;"|'''Arduino Pin'''
| align="center" style="background:#f0f0f0;"|'''Description'''
|-
| D0||XBEE_TX
|-
| D1||XBEE_RX
|-
| D2||nRF24L01_IRQ & STD Button
|-
| D3||IR_TX*
|-
| D4||SD_CS
|-
| D5||IR_RX*
|-
| D6||LED1*
|-
| D7||LED2*
|-
| D8||-
|-
| D9||nRF24L01_CE
|-
| D10||nRF24L01_CS
|-
| D11||MOSI
|-
| D12||MISO
|-
| D13||SCK
|-
| A0||A0 Button
|-
| A1||-
|-
| A2||-
|-
| A3||-
|-
| A4||SHT10_SDA
|-
| A5||SHT10_SCL
|-
|}
*IR_TX: when D3 is set as high level switch, IR Diode will emit signals out. When D3 is set as low level switch, IR Diode won’t work.
*IR_RX: Use HS0038B as IR receiving module
*Jumpers:
:Jumpers can directly connect to Arduino’s IO. If you don’t need them or their corresponding pins are occupied, you can remove the jumpers.
:*A0: insert a 10K resistance to A0 button
:*LED1: connect to D6 pin. If the output voltage is high, LED1 turns on.
:*LED2: connect to D7 pin. If the output voltage is high, LED1 turns on.
*Switch: Set the switch level according to Arduino main board. When the mainboard is set in 5V, you should turn the switch to 5V; when in 3.3V, you should turn to 3.3V.

Pin Map

Arduino Pin Description
D0 XBEE_TX
D1 XBEE_RX
D2 nRF24L01_IRQ & STD Button
D3 IR_TX*
D4 SD_CS
D5 IR_RX*
D6 LED1*
D7 LED2*
D8 -
D9 nRF24L01_CE
D10 nRF24L01_CS
D11 MOSI
D12 MISO
D13 SCK
A0 A0 Button
A1 -
A2 -
A3 -
A4 SHT10_SDA
A5 SHT10_SCL
  • IR_TX: when D3 is set as high level switch, IR Diode will emit signals out. When D3 is set as low level switch, IR Diode won’t work.
  • IR_RX: Use HS0038B as IR receiving module
  • Jumpers:
Jumpers can directly connect to Arduino’s IO. If you don’t need them or their corresponding pins are occupied, you can remove the jumpers.
  • A0: insert a 10K resistance to A0 button
  • LED1: connect to D6 pin. If the output voltage is high, LED1 turns on.
  • LED2: connect to D7 pin. If the output voltage is high, LED1 turns on.
  • Switch: Set the switch level according to Arduino main board. When the mainboard is set in 5V, you should turn the switch to 5V; when in 3.3V, you should turn to 3.3V.
Retrieved from "https://wiki.iteadstudio.com/index.php?title=Translations:IR_Shield/7/en&oldid=2392"