Difference between revisions of "RASPBERRY PI OLED ADD-ON/zh-cn"

From ITEAD Wiki
Jump to: navigation, search
(Created page with "OLED Add-on是为树莓派量身定制的，板载一块0.96" 128*64 OLED屏幕，控制芯片为SSD1306，每一个像素点都可以通过SSD1306独立控制点亮或者关...")
(Created page with "我们不仅仅只是提供一块可以方便的插在树莓派上面的板子，还为其配套提供了SDK，移植了Arduino上的驱动程序。安装完SDK后，就可以...")
Line 5: Line 5:
 
OLED Add-on是为树莓派量身定制的，板载一块0.96" 128*64 OLED屏幕，控制芯片为SSD1306，每一个像素点都可以通过SSD1306独立控制点亮或者关闭。
 
OLED Add-on是为树莓派量身定制的，板载一块0.96" 128*64 OLED屏幕，控制芯片为SSD1306，每一个像素点都可以通过SSD1306独立控制点亮或者关闭。
  
−
We not only offer an easily-plugged add-on for Raspberry Pi, but also provide an SDK that help you transplant Arduino’s driver into Raspberry Pi. After installing the SDK, you can drive this add-on as easily as you do on Arduino.
+
我们不仅仅只是提供一块可以方便的插在树莓派上面的板子，还为其配套提供了SDK，移植了Arduino上的驱动程序。安装完SDK后，就可以像在Arduino平台底下一样，非常轻松的驱动这块板子。
  
 
==Features==
 
==Features==

Revision as of 09:18, 17 July 2014

概述

IM140714003 3.JPG

市面上很少能找到为树莓派量身定制的OLED屏幕，/在很多应用项目中，我们仅需要显示非常简单的一些信息，比如系统状态、IP等信息，/或者对便携性有较高需求，这时候用HDMI去接一个大屏幕明显不合适，一个小巧的OLED屏幕刚好能满足这种需求。

OLED Add-on是为树莓派量身定制的，板载一块0.96" 128*64 OLED屏幕，控制芯片为SSD1306，每一个像素点都可以通过SSD1306独立控制点亮或者关闭。

我们不仅仅只是提供一块可以方便的插在树莓派上面的板子，还为其配套提供了SDK，移植了Arduino上的驱动程序。安装完SDK后，就可以像在Arduino平台底下一样，非常轻松的驱动这块板子。

Features

  • Customized for Raspberry Pi, plug and play without wiring
  • 0.96" OLED with 128*64 pixels
  • Stackable
  • Coming with one Grove interface for Electronic bricks


Specification

PCB size 48.35mm X 48.47mm X1.6mm
Interface RPI 26pins Interface X2,UART

Electrical Characteristics

Characteristics Symbol Min Typ Max Unit
Power supply voltage VDD 3 3.3 3.5 V
High input voltage VIH 0.8XVDD - VDD V
Low input voltage VIL 0 - 0.2XVDD V
Operation current for VDD IDD - 180 300 uA

Hardware

IM140714003pic1.jpg IM140714003pic2.jpg IM140714003pic3.jpg

Pin Map

Pin Index Pin Name OLED 2864 pin Description
1 3V3 -
2 5V -
3 SDA SDA
4 5V -
5 SCL SCL
6 GND -
7 GPIO7 UART TXD
8 TXD
9 GND
10 RXD UART RXD
11 GPIO0
12 GPIO1
13 GPIO2
14 GND
15 GPIO3
16 GPIO4 RST#
17 3V3
18 GPIO5
19 MOSI
20 GND
21 MISO
22 GPIO6
23 SCK
24 CE0
25 GND
26 CE1

Instruction

  • Plug OLED add-on into Raspberry Pi and power it
  • modify the file /etc/modprobe.d/raspi-balcklist.conf
modified codes as below
blacklist spi-bcm2708
blacklist i2c-bcm2708
  • modify /etc/modules
add a line in the end as below:
i2c-dev
  • reboot
  • Download the SDK from this link: https://github.com/iteadsw/SDK and then install it
  • Enter into the directory libraries/itead_SSD1306/examples/oled_Animation_Sample/, then compile and run this file oled_Animation_Sample.ino
Command as below to compile oled_Animation_Sample.ino
$ iteadcompile OLED oled_Animation_Sample.ino
Command to run this program
$ sudo ./OLED
  • When the compilation is done, you can see a little man dancing on OLED.

IM140714003in1.gif

Download

File:SCH IM140714003.pdf

Useful Link

https://github.com/iteadsw/SDK https://github.com/iteadsw/SDK/tree/master/libraries/itead_SSD1306

Retrieved from "https://wiki.iteadstudio.com/index.php?title=RASPBERRY_PI_OLED_ADD-ON/zh-cn&oldid=2103"