Difference between revisions of "RASPBERRY PI OLED ADD-ON/zh-cn"

From ITEAD Wiki
Jump to: navigation, search
(Created page with "==概述== right 市面上很少能找到为树莓派量身定制的OLED屏幕，/在很多应用项目中，我们仅需要显示非常...")
m
Line 2: Line 2:
 
[[File:IM140714003_3.JPG|thumb|400px|right]]
 
[[File:IM140714003_3.JPG|thumb|400px|right]]
 
市面上很少能找到为树莓派量身定制的OLED屏幕，/在很多应用项目中，我们仅需要显示非常简单的一些信息，比如系统状态、IP等信息，/或者对便携性有较高需求，这时候用HDMI去接一个大屏幕明显不合适，一个小巧的OLED屏幕刚好能满足这种需求。
 
市面上很少能找到为树莓派量身定制的OLED屏幕，/在很多应用项目中，我们仅需要显示非常简单的一些信息，比如系统状态、IP等信息，/或者对便携性有较高需求，这时候用HDMI去接一个大屏幕明显不合适，一个小巧的OLED屏幕刚好能满足这种需求。
−
 
−
OLED Add-on是为树莓派量身定制的，板载一块0.96" 128*64 OLED屏幕，控制芯片为SSD1306，每一个像素点都可以通过SSD1306独立控制点亮或者关闭。
 
−
 
−
我们不仅仅只是提供一块可以方便的插在树莓派上面的板子，还为其配套提供了SDK，移植了Arduino上的驱动程序。安装完SDK后，就可以像在Arduino平台底下一样，非常轻松的驱动这块板子。
 
  
 
OLED add-on with built-in 0.96" 128*64 OLED and SSD1306 control chip is customized for Raspberry Pi. Every single pixel in OLED can be lighted up or off by this SSD1306 control chip.
 
OLED add-on with built-in 0.96" 128*64 OLED and SSD1306 control chip is customized for Raspberry Pi. Every single pixel in OLED can be lighted up or off by this SSD1306 control chip.

Revision as of 09:18, 17 July 2014

概述

IM140714003 3.JPG

市面上很少能找到为树莓派量身定制的OLED屏幕，/在很多应用项目中，我们仅需要显示非常简单的一些信息，比如系统状态、IP等信息，/或者对便携性有较高需求，这时候用HDMI去接一个大屏幕明显不合适，一个小巧的OLED屏幕刚好能满足这种需求。

OLED add-on with built-in 0.96" 128*64 OLED and SSD1306 control chip is customized for Raspberry Pi. Every single pixel in OLED can be lighted up or off by this SSD1306 control chip.

We not only offer an easily-plugged add-on for Raspberry Pi, but also provide an SDK that help you transplant Arduino’s driver into Raspberry Pi. After installing the SDK, you can drive this add-on as easily as you do on Arduino.

Features

  • Customized for Raspberry Pi, plug and play without wiring
  • 0.96" OLED with 128*64 pixels
  • Stackable
  • Coming with one Grove interface for Electronic bricks


Specification

PCB size 48.35mm X 48.47mm X1.6mm
Interface RPI 26pins Interface X2,UART

Electrical Characteristics

Characteristics Symbol Min Typ Max Unit
Power supply voltage VDD 3 3.3 3.5 V
High input voltage VIH 0.8XVDD - VDD V
Low input voltage VIL 0 - 0.2XVDD V
Operation current for VDD IDD - 180 300 uA

Hardware

IM140714003pic1.jpg IM140714003pic2.jpg IM140714003pic3.jpg

Pin Map

Pin Index Pin Name OLED 2864 pin Description
1 3V3 -
2 5V -
3 SDA SDA
4 5V -
5 SCL SCL
6 GND -
7 GPIO7 UART TXD
8 TXD
9 GND
10 RXD UART RXD
11 GPIO0
12 GPIO1
13 GPIO2
14 GND
15 GPIO3
16 GPIO4 RST#
17 3V3
18 GPIO5
19 MOSI
20 GND
21 MISO
22 GPIO6
23 SCK
24 CE0
25 GND
26 CE1

Instruction

  • Plug OLED add-on into Raspberry Pi and power it
  • modify the file /etc/modprobe.d/raspi-balcklist.conf
modified codes as below
blacklist spi-bcm2708
blacklist i2c-bcm2708
  • modify /etc/modules
add a line in the end as below:
i2c-dev
  • reboot
  • Download the SDK from this link: https://github.com/iteadsw/SDK and then install it
  • Enter into the directory libraries/itead_SSD1306/examples/oled_Animation_Sample/, then compile and run this file oled_Animation_Sample.ino
Command as below to compile oled_Animation_Sample.ino
$ iteadcompile OLED oled_Animation_Sample.ino
Command to run this program
$ sudo ./OLED
  • When the compilation is done, you can see a little man dancing on OLED.

IM140714003in1.gif

Download

File:SCH IM140714003.pdf

Useful Link

https://github.com/iteadsw/SDK https://github.com/iteadsw/SDK/tree/master/libraries/itead_SSD1306

Retrieved from "https://wiki.iteadstudio.com/index.php?title=RASPBERRY_PI_OLED_ADD-ON/zh-cn&oldid=2098"